Manuals / Meridian Audio / Home Audio / Home Theater System

Meridian Audio G61 manual Not Con, Auto, I n s t a l l i n g t h e, $IGITALI3URROUND #ONTROLLER

Models: G61

1 59

Download 59 pages 26.08 Kb

Page 19

'$IGITALI3URROUND #ONTROLLER

1 4

I n s t a l l i n g t h e

d i g i t a l s u r r o u n d

c o n t r o l l e r

To connect to other Meridian G Series, 500 Series, or 800 Series equipment

'$IGITALI3URROUND #ONTROLLER

''3ERIES 3ERIES ORO 3ERIES UNITE

#/--3

#/--3

#/--3-,%!$

#/--3-,%!$

In a system of Meridian products the products should be linked together in a chain, via the COMMS sockets, using the Comms leads supplied with each product. The sequence in which you connect the units is not important.

One of the products acts as the controller for the system, receiving infra-red commands from the MSR+, and then, if appropriate, relaying them to the other products via the Comms link. The following procedure should be used to set up the Comms correctly between several products:

•Switch all the units to standby.

•Press Clear (MSR+).

Each unit will display:

All the other units will be configured as non-controllers, and display:

Not Con.

The system is now ready for use.

If the automatic setup does not work, first make sure you are operating the MSR+ from a position where all the units can receive the infra-red, and try again. Then:

•Check that none of the units have been configured to be IR Controller; see Configuring other settings, page 22. Either all products should be set to Auto, or one should be configured as Controller and the others as Not Controller.

Auto

One unit will then be designated as the controller, and display:

Note: Do not, under any circumstances, connect any equipment other than Meridian G Series, 500 Series, or 800 Series to any socket marked COMMS on the back of the product.

Con.

Image 19

Meridian Audio G61 manual Not Con, Auto, I n s t a l l i n g t h e, d i g i t a l s u r r o u n d c o n t r o l l e r

Contents

I N S T A L L A T I O N G U I D E M E R I D I A N G S E R I E SG61 Digital Surround Controller Installation GuideRadio interference Safety warningsTo avoid overheating To avoid interferenceContents i P r e f a c e Copyright and acknowledgementsSales and service in the UK Sales and service in the USAInputs Introduction1 I n t r o d u c t i o n 2 I n t r o d u c t i o n 3 I n t r o d u c t i o n Specifications4 I n t r o d u c t i o n Unpacking Installing the digital surround controller6 I n s t a l l i n g t h e Audio inputsd i g i t a l s u r r o u n d c o n t r o l l e r 46 TUNER 7 I n s t a l l i n g t h ed i g i t a l s u r r o u n d c o n t r o l l e r BIT #$ 0LAYERd i g i t a l s u r r o u n d c o n t r o l l e r 8 I n s t a l l i n g t h e3!#$$6$ ! PLAYER 9 I n s t a l l i n g t h e Audio outputsd i g i t a l s u r r o u n d c o n t r o l l e r 3 PATCH BOX 1 I n s t a l l i n g t h ed i g i t a l s u r r o u n d c o n t r o l l e r $30#d i g i t a l s u r r o u n d c o n t r o l l e r 1 I n s t a l l i n g t h e$IGITALI3URROUND #ONTROLLER Use RZ and LZ if you have two subwoofers 1 I n s t a l l i n g t h ed i g i t a l s u r r o u n d c o n t r o l l e r 3UBWOOFER $IGITALI3URROUND #ONTROLLER1 I n s t a l l i n g t h e Communications connectionsd i g i t a l s u r r o u n d c o n t r o l l e r 1 I n s t a l l i n g t h e Switch all the units to standbyNot Con AutoConfiguration Wizard Configuring the digital surround controllerType Stage 1 Resetting the product1 Reset settings Reset all settings?Music Sub TypesType SpeakersEither Stage 2 Configuring speakers2 Select speakers EitherDescription Speaker optionsOption Valuesin use Stage 3 Configuring sources3 Configure sources RadioSource options Either Stage 4 Configuring other settings4 Other settings used as necessarySettings Page Calibrating the system Using a Sound Pressure Level meterIntroduction Either Left Level +0.0dBWizard complete 2 C a l i b r a t i n g t h e s y s t e mLeft Level +0.0dB Calibration testsLevels DistanceLeft Fine tuningPhase Left DistanceC a l i b r a t i n g t h e s y s t e m Speaker sizeSizes set to zero Left SizeCD Xover 85Hz Using the Sine/Sub/Sens controlsSinewave sweep test Subwoofer crossover frequencyPause CD Sine 80.0Hz88.5Hz 81.5HzDVD Not Analogue Setting up sources1.4V Peak TV 2.0V ClipDSP presets DSP presets3 D S P p r e s e t s Parameter Standard parametersDefault 3 D S P p r e s e t sMusic DSP presets for two-channelmaterialMusic and Trifield DSP preset parameters 3 D S P p r e s e t sSuper Ambisonics and Super DSP preset parameters3 D S P p r e s e t s AmbisonicsMusicLogic 3 D S P p r e s e t sPLIIx Movie and PLIIx THX PLIIx Movie and PLIIx THX DSP preset parameters3 D S P p r e s e t s Stereo and DirectTV Logic 3 D S P p r e s e t s4 D S P p r e s e t s DSP presets for multichannel material4 D S P p r e s e t s THX DSP preset parameters4 D S P p r e s e t s Using dynamic range controlAmbisonics To save the preset settings Defining your own presets4 D S P p r e s e t s Stored To clear a user-definedpreset4 D S P p r e s e t s General operating problems Troubleshooting4 Tr o u b l e s h o o t i n g Unit is overheating Audio problems4 Tr o u b l e s h o o t i n g Remote not workingSound not clear Audible hiss at high volume settingsConfiguration Program Guide 4 Tr o u b l e s h o o t i n gsource 4 Tr o u b l e s h o o t i n gCleaning Maintenance4 Tr o u b l e s h o o t i n g 5 Tr o u b l e s h o o t i n g Service and guaranteeService GuaranteeI n d e Index5 I n d e 5 I n d e 5 I n d e