9
Digital Temperature Controller
PN 36056
Service instructions
+ 
LOCK SERVICE
KEY KEY
Push the lock key and the service key together to reach SP LOK, then use the service key to step through the other functions listed
below.
Use the arrow keys to change the function settings. Factory settings are as shown below.
Indicator flashing
Indicator not flashing
no | HEAT ON |
| d E | g | F | HEAT ON | 5 E | HEAT ON | 6 8 F | HEAT ON | ||
| SET PT | SET PT | ||||||||||
SET PT |
| SET PT | ||||||||||
ACTUAL |
|
| ACTUAL | SP LOCK | ACTUAL | SP LOCK |
| ACTUAL | ||||
SP LOCK | TEMP |
| SP LOCK |
| TEMP | OVER TEMP | TEMP | OVER TEMP |
| TEMP | ||
OVER TEMP |
| OVER TEMP |
|
| ||||||||
|
|
|
|
|
|
| This function will record the | |||||
NO = set point |
|
| F = degrees Fahrenheit | SET = set point display | ||||||||
| unlocked |
|
| C = degrees Celsius |
| ACT = actual temperature | highest ambient | temperature of | ||||
YES = set point |
|
|
|
|
|
| display. |
| the temperature | controller; | ||
| locked |
|
|
|
|
|
|
|
| 68ºF/20ºC is the | original | |
|
|
|
|
|
|
|
|
| reading. |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
If | the “On/Of” | setting | is chosen, the | This | display | allows programming the | controller for either | the |
|
|
| |
“LyES” display | will be | bypassed. |
|
|
|
| ||||||
| standard O N / O F F mode or the PID (360EWB models) mode for |
|
|
| ||||||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
| the | modulating gas control system. |
|
|
|
|
| |
L | y | E S |
|
| O n O F | or | P d | b | 0 | ACTUAL | ||
|
|
|
|
|
|
|
|
|
|
| HEAT ON | |
|
|
|
|
|
|
|
|
|
|
| SET PT | |
Confirms | that | the Pid |
|
|
|
|
|
| SP LOCK | TEMP | ||
|
| + | Push the lock key and the display key to | OVER TEMP | ||||||||
1) |
|
| ||||||||||
(Modulating) | setting |
|
|
|
| |||||||
| enable the programming function of the | This display | is the BIAS | (actual | ||||||||
has been locked in if |
|
|
| |||||||||
| LOCK | DISPLAY | “OnOF or | “Pid” temperature control | temperature) | adjustment | scale | |||||
the Pid setting was |
| |||||||||||
chosen. |
|
|
| KEY | KEY | system. |
| which is Factory set at zero. | ||||
|
|
|
|
|
| The Factory must be consulted | ||||||
|
|
|
| 2) |
| OnOF = standard on/off temperature cycling system (gas & electric) | ||||||
|
|
|
|
| for any adjustments to the | |||||||
|
|
|
|
|
| PiD = modulating temperature proportioning system | BIAS. |
|
| |||
|
|
|
|
|
| (gas 360 EWB only) |
|
|
| |||
Figure 14 - Service Instructions
