Manuals / Middleby Marshall / Kitchen Appliance / Oven

Middleby Marshall V. Assembly, 2-13, Exploded View - Upper Oven Stand, Section Installation

Models: Oven

1 30

Download 30 pages 19.19 Kb

Page 13

Image 13

SECTION 2

INSTALLATION

V. ASSEMBLY

If the installation includes upper ovens mounted atop lower ovens, the ovens must be stacked before joining the tandem ovens together.

If the installation includes ovens that are to be mounted on stands, assemble the ovens to the stands before joining the ovens together. An exploded view of the stand is shown in Figure 2-14.

Figure 2-14

Exploded View - Upper Oven Stand

2-13

Page 13

Image 13

Middleby Marshall owner manual V. Assembly, 2-13, Exploded View - Upper Oven Stand, Section Installation

Contents

SECTION INSTALLATION SECTION INSTALLATIONI. UNLOADING/UNPACKING There must be adequate clearanceFigure 2-1 - Ventilation Hood Dimensions RECOMMENDATIONS ONLY II. INSTALLATION, PREPARATION, AND SUPPLYSECTION INSTALLATION SECTION INSTALLATION III. VENTILATION SYSTEMRESTRICT SERVICE ACCESS LEAD TO INCREASED SERVICE EXPENSES FOR THE OWNERSECTION INSTALLATION Figure 2-2 - INSTALLATION KITDescription PS360U/WB-U Quad TandemDimensions and Data PS360WB-L Tandem Dimensions and Data PS360L TandemSECTION INSTALLATION Dimensions and Data PS360WB Double Tandem Dimensions and Data PS360 Double TandemSECTION INSTALLATION INSTALLATION Dimensions and Data PS360U Tri TandemSECTION SECTION 2 INSTALLATION Dimensions and Data PS360WB-U Tri TandemINSTALLATION Dimensions and Data PS360U Quad TandemSECTION 2-10 Dimensions and Data PS360WB-U Quad TandemSECTION 2 INSTALLATION Thermocouple Installation Locations IV. THERMOCOUPLE INSTALLATION2-11 Placing the Thermocouple LeadsThermocouple Lead Connections 2-12SECTION INSTALLATION 8 = White = Positive 7 = Red = Negative R = No Connection2-13 V. ASSEMBLYExploded View - Upper Oven Stand SECTION INSTALLATIONLEFT OVEN 2-14RIGHT OVEN Oven Positioning and Alignment2-15 Aligning the Ovens for AssemblyBolts and Spacers SECTION INSTALLATIONChecking Track Rail Alignment 2-16Trim Strip Positioning SECTION INSTALLATION2-17 Transition Frame PlacementFigure 2-22a Support Brackets Lower Oven Figure 2-22b Support Brackets Upper Oven2-18 Installing the Transition Floor PanelReplacing the Transition Frame SECTION INSTALLATIONFigure 2-25c Installing the Conveyor Frame Quad Tandem Ovens Figure 2-25b Installing the Conveyor Frame Tri Tandem Ovens2-19 Figure 2-25aConveyor Link Orientation 2-20Inside Master Links Outside Master LinksConveyor Motor and Drive Chain Assembly Transition Assembly2-21 SECTION 2 INSTALLATIONGAS SUPPLY GAS OVEN ROUGH-INELECTRICAL SUPPLY DO NOT USE CONDUIT FOR GROUND2-23 VI. ELECTRICAL CONNECTIONJunction Connection Box Lower Oven Junction Connection Box Upper OvenTypical Oven Data Plate - Models PS360/PS360WB 2-24SECTION INSTALLATION VII. GAS SUPPLY FOR GAS HEATED OVENS Flexible Hose Connector Installation2-25 SECTION INSTALLATION2-26 VIII. PREPARATION FOR VARIOUS GASESSECTION INSTALLATION FOR USE WITH NATURAL GASBurner/Piping Assembly INSTALLATIONSECTION 2-27IX. CHANGING ORIFICES X. VOLUMETRIC METHOD2-28 SECTION INSTALLATION2-29 XI. VARIATIONS OF RATED SUPPLY PRESSURESSECTION INSTALLATION TO CHECK GAS SUPPLY PRESSURESECTION INSTALLATION 2-30SPECIAL NOTICES