Manuals / Miller Electric / Lawn and Garden / Portable Generator

Miller Electric 145 DX manual Description Of Controls DX Models See Section

Models: 145 DX

1 56
Download 56 pages 7.47 Kb
Page 25
Image 25

6-4. Description Of Controls (DX Models) (See Section 6-3)

1 Engine Switch

Use switch to control ignition circuit. Turn switch to Start position for electric start. Turn switch to On position to start engine using starter handle (recoil). Turn switch to Off posi- tion to stop engine.

2 Low Oil Level Light

Light goes on and engine stops if engine oil level is too low.

Engine cannot be restarted until sufficient oil is added.

YStop engine and add oil if light goes on (see Section 5-5).

3 Starter Handle

Use starter handle to start unit if electric start does not work.

4 Choke Control

Use control to change engine air/fuel mix. Move control to far right if starting a cold en- gine. Move control to far left if starting a warm engine.

The engine starts at weld/power speed and runs at weld/power speed under weld or gen- erator power load. The engine returns to idle speed 12 seconds after start-up or after weld or generator power load is removed.

To Start:

DOpen fuel valve (see Section 5-5).

DSet choke.

DElectric-Start: Turn Engine switch to Start position.

Recoil: Turn Engine switch to On posi- tion. Pull starter handle until engine starts.

DOpen choke as engine warms.

YIf the engine does not start, let engine come to a complete stop before at- tempting restart.

To Stop:

DTurn Engine switch to Off.

.Always close fuel valve after stopping unit. Moving unit with fuel valve open may cause carburetor flooding and make starting difficult.

5 Welding Range Table

Use table to determine correct weld amper- age based on electrode size, type, and mate- rial thickness.

6 Run / Idle Switch

Use switch to select whether the engine stays at run speed continuously or whether the auto idle feature is enabled so engine speed re- turns to idle speed after start−up or after weld or generator load is removed.

7 Weld Output Control

.Set control at maximum for full generator power output at AC receptacles.

Use control to select weld amperage. Control may be adjusted while welding.

To Set Weld Output Control: Use table to determine correct size electrode for weld am- perage. Select electrode type and set control to corresponding amperage range on name- plate. Adjust control to obtain desired weld performance.

EXAMPLE:

Electrode Diameter: 1/8

Electrode Type: E-6013

Current Control Setting: 90 − 120 A 8 Hourmeter

Use hourmeter to help schedule routine main- tenance.

Notes

Work like a Pro!

Pros weld and cut safely. Read the safety rules at the beginning of this manual.

OM-4417 Page 21

Page 24 Page 26
Page 25
Image 25
Miller Electric 145 DX manual Description Of Controls DX Models See Section
Page 24 Page 26

145 DX specifications

Miller Electric has established itself as a leading name in the welding industry, and the Miller Electric 145 DX and 145 are notable additions to its lineup of innovative welding machines. Designed to offer versatility and efficiency, these units cater to both novice welders and seasoned professionals seeking reliable equipment for various welding applications.

One of the key features of the Miller Electric 145 DX and 145 is their advanced welding technology. Both models utilize inverter technology, which allows for a compact design while delivering exceptional power. This inverter design not only increases efficiency but also reduces energy consumption, making it an environmentally friendly choice. The lightweight nature of these units makes them highly portable, allowing users to easily transport them to job sites or move them around the workshop.

The Miller Electric 145 DX model incorporates a digital interface that simplifies set-up and operation. This user-friendly digital display shows critical parameters such as voltage and amperage, helping the operator make quick adjustments on-the-fly for optimal results. The advanced Auto-Set feature adjusts the machine settings automatically based on the material thickness and type, significantly reducing the learning curve for inexperienced welders.

Both the 145 DX and 145 models can handle a variety of welding processes, including MIG and TIG welding. This versatility makes them suitable for a wide range of applications, from automotive repair and fabrication to metal sculpture and DIY projects. The machines are capable of welding aluminum, stainless steel, and mild steel with ease, providing excellent penetration and bead appearance.

Another noteworthy characteristic of the Miller Electric 145 series is their reliability and durability. Designed with robust components that can withstand challenging working environments, these machines are built to last. The thermal overload protection feature ensures the units do not overheat, safeguarding the internal components and ensuring a longer operational life.

In summary, the Miller Electric 145 DX and 145 stand out in the welding equipment market due to their advanced inverter technology, user-friendly digital interfaces, versatile capabilities, and durability. They are ideal choices for anyone looking to elevate their welding experience, delivering consistent and reliable performance across a variety of projects.