Connecting Input Power, 460 mm | Miller Electric 375 X-TREME

.A complete Parts List is available at www.MillerWelds.com

4-11. Connecting Input Power

Y Do Not cut off power cord connector and rewire. The power cord connector and plugs will work with standard NEMA receptacles. Modifying power cord, connector, and plugs will void product warranty.

18 in

(460 mm)

.Serial Number/Rating Label located on bottom of base; use label to determine input power for unit.

1

2 3

18 in

(460 mm)

4 5

804 504-A

YInstallation must meet all National and Local Codes − have only qualified persons make this installation.

YSpecial installation may be required where gasoline or volatile liquids are present − see NEC Article 511 or CEC Section 20.

.The Auto-Line circuitry in this unit automatically links the power source to

the primary voltage being applied, either 115 or 230 VAC.

For 120 volts ac input power, a 15 or 20 ampere individual branch circuit protected by time-delay fuses or circuit breaker is required. For 240 volts ac input power, see Section 4-8.

1Power Cord Connector

2Plug − NEMA Type 5−15P

3Receptacle − NEMA Type 5−15R (Customer Supplied)

4Plug − NEMA Type 6−50P

5Receptacle − NEMA Type 6−50R (Customer Supplied)

Select plug for power supply receptacle available at site. Install plug onto power cord adapter. As threaded collar is tight- ened, push plug onto adapter until collar is completely tight.

Connect plug to receptacle.

OM-225 216 Page 14

Image 18

Miller Electric 375 X-TREME, ICE-27T manual Connecting Input Power, 460 mm

Contents

Description OM-225 216FProcesses File Plasma Cutters From Miller to You Table of Contents Page Plasma Arc Cutting Hazards Symbol UsageMarks a special safety message Cutting can cause fire or explosion ARC Rays can burn eyes and skin Exploding Parts can injureFlying Sparks can cause injury Noise can damage hearing California Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers UNE Décharge Électrique peut entraîner la mort Signification des symbolesLE Coupage présente un risque de feu ou d’explosion Identifie un message de sécurité particulier LES Fumées ET LES GAZ peuvent être dangereux Risque de blessure en casLE Bruit peut endommager l’ouïe LE Plasma D’ARC peut entraîner des blessures LA Chute DE L’APPAREIL peut blesser DES Pieces Chaudes peuvent pro- voquer des brûlures gravesDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU LE Coupage Ã L’ARC peut causer des interférence Principales normes de sécuritéInformation sur les champs électromagnétiques Consignes relatives aux stimulateurs cardiaques Symbols And Definitions SpecificationsSpecifications For Torch Power Source Dimensions And Weight Torch Dimensions And WeightDuty Cycle And Overheating Connecting Gas/Air Supply Connecting Work Clamp 60 Hz Electrical Service Guide For 240 VACExtension Cord Data Input Voltage 240 Input Amperes At Rated Output Connecting 1-Phase Input Power For 240 VAC Connecting Input Power 460 mm − Operation Controls Trigger Safety Lock Cutting Speed Example Of Cutting Operation When trigger is pressedSequence Of Operation Pilot arc starts immediately Routine Maintenance Overload Protection Wrapper Check Bus Wrapper RemovalTurn Off Removing wrapper Wrapper Torx Screws Fine Thread DC Bus Voltage Check Checking Or Replacing Filter Element Checking Torch Shield Cup Shutdown System Shield Cup Turn Off power source before checking torch parts Checking/Replacing Retaining Cup, Tip, And Electrode Torch And Work Cable Connections Torch ConnectionsWork Cable Connections OM-225 216 − Electrical Diagram 224 682-B Recommended Spare Parts Recommended Spare Parts OM-225 216 Page Service Support Owner’s Record Miller Electric Mfg. Co