Tools Needed Red, White, Black | Miller Electric R-115 instruction

3-15. Connection For Lincoln Welding Power Sources With Terminal Strip Connections

		. Make ground lead connections
		according to Section 3-9before
		following this procedure.
		3
	C D	E
A	B
1
		2
		GND
Tools Needed:		2 (Red)
		4 (Orange)
		31 (White)
		32 (Black)
		1/4 in

1Terminal Block 1T

2Interconnecting Power Cord

3Green Lead (Connected To Ground In Section 3-9)

Connect remaining leads to terminal block as follows:

A:115 VAC/Neutral Lead

B:115 VAC/Hot Lead

C:No Connection

D:Dry Contact Closure w/Respect To Terminal E Lead

E:115 VAC/Contact Closure Lead

.For welding power sources

requiring dry contact closure, move lead 38 at terminal block to terminal D.

Secure strain relief clamp around cord.

Reinstall and secure wrapper to unit.

Connect remaining end of cord to welding power source.

Ref. 802 310 / Ref. 193 749

3-16. Connection For AIRCO Welding Power Sources With Two-Prong Twistlock And 115 Volts AC Receptacles

		3
	C	D E
A B	C
A B
1
		2
Tools Needed:
		1/4 in

.Make ground lead connections

according to Section 3-9before following this procedure.

1Terminal Block 1T

2Interconnecting Power Cord

3Green Lead (Connected To Ground In Section 3-9)

Connect remaining leads to terminal block as follows:

A:115 VAC/Neutral Lead

B:115 VAC/Hot Lead

C:No Connection

D:No Connection

E:115 VAC/Contact Closure Lead

Secure strain relief clamp around cord.

Reinstall and secure wrapper to unit.

Connect remaining end of cord to welding power source.

Ref. 802 310 / Ref. 193 749

OM-193 471 Page 17

Image 21

Miller Electric R-115 manual Tools Needed Red, White, Black

Contents

Processes OM-193 471PDescription File MIG Gmaw From Miller to You Table of Contents Page Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can kill Welding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or kill California Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier Signifie Note n’est pas relatif à la sécurité Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures graves LA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessures En ce qui concerne les stimulateurs cardiaques Principales normes de sécurité Welding Power SpecificationsWire Power Rear Panel Connections And Power Switch Location Equipment Connection DiagramsGun Recommendation Table Shielding gas pressure not to exceed 100 PSI 689 kPa Connecting Welding Gun And Weld Cable Installing Wire Guide And Drive Roll Wood Installing And Threading Welding Wire Ground lead must be wrapped For welding power sources reQuiring dry contact closure Move lead 38 at terminal block According to -9before Make ground lead connections To Terminal E Lead For Welding power sources Tools Needed Red WhiteBlack White Lead Motor Start/Burnback Control Optional Side Panel Controls Front Panel Controls Routine Maintenance MonthsOverload Protection Trouble Remedy Troubleshooting − Electrical Diagram − Parts List PLG4 Hardware is common Drive Assembly, Wire -2 Item Drive Roll & Wire Guide Kits OM-193 471 OM-193 471 OM-193 471 Support Service Miller Electric Mfg. Co Owner’s Record