Mode Switch Settings For CC/CV Models | Miller Electric XMT 456 CC

5-6. Mode Switch Settings For CC/CV Models

.The SMAW modes provide the Adaptive Hot Start™ feature, which automatically increases the output amperage at the start of a weld should the start require it. This eliminates electrode sticking at arc start.

Mode		Output Control
	Select:	or	Amp
Scratch Start TIG (GTAW)
	Weld:
Lift-Arc Trigger	Select:	or	Amp
Lift-Arc Trigger
Hold TIG (GTAW)
	Requires:		Control
TIG (GTAW) With	Select:	or	Amp
HF Unit,
Pulsing Device,
Or Remote Control	Requires:		Control
	Requires:		Control
	Select:	or	Volt
MIG (GMAW)
	Requires:	Feeder
MIG (GMAW) With	Select:	or	Amp
Voltage Sensing
Wire Feeder	Weld:
	Weld:
Pulsed MIG	Select:	Volt
(GMAW-P)	Select:	Volt
(Requires an
external
pulsing device.)	Requires:		Feeder or Control
	Select:	or	Amp
Remote
Control SMAW	Requires:		Control
	Requires:		Control
Panel Control	Select:	or	Amp
Panel Control
SMAW
	Weld

OM-203 034 Page 25

Page 29

Image 29

Miller Electric XMT 456 CC, XMT 456CV manual Mode Switch Settings For CC/CV Models

Contents

Processes OM-203 034NDescription File MIG Gmaw From Miller to You Table of Contents Decstat6/05 DirectivesStandards Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burns ARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyes Fire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injury California Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical Devices UNE Décharge Électrique peut entraîner la mort Symboles utilisés LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesser LE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-203 034 Keep your head out of the fumes Disconnect input plug or power before working on machineManufacturer’s Warning Label Definitions 60 s I1max Symbols And DefinitionsI1eff Weee Label Manufacturer’s Rating Labels Duty Cycle And Overheating Specifications CV Modes CC Modes Dimensions And WeightVolt-Ampere Curves Selecting a Location Connecting To Weld TerminalsMovement Tipping Location 350 ft 400 ft Put terminals Weld Output Terminals And Selecting Cable SizesARC Welding can cause Electromagnetic Interference Remote 14 Receptacle Information Connecting Weld Output Cables Hz Three Phase Electrical Service GuideVolts AC Duplex Receptacle Input Voltage Input Filter Board Connecting Input PowerAlways connect grounding conductor first L21 Tools Needed Mode Control Mode And Voltage Control For CV Only ModelsFront Panel Controls For CV Only Models Voltage Control Power Switch Preset Volts BlankMeter Functions For CV Only Models Front Panel Controls For CC/CV Models Panel Control Gtaw Meter Functions For CC/CV ModelsHold TIG Gtaw Blank Pulsed MIG Mode Switch Settings For CC/CV Models Touch Seconds Do not Strike Like a Match Lift-Arc TIG Procedure For CC/CV Models Blowing Out Inside Of Unit Do not remove case when blowing out inside of unit Removing Case and Measuring Input Capacitor Voltage Voltmeter/Ammeter Help Displays Reset circuit breaker CB1 see Section Troubleshooting OM-203 034 − Electrical Diagram 203 505-A Circuit Diagram For CC/CV Welding Power Source 204 950−B 39 40 41 Complete Assembly Dia Part Description Quantity Mkgs 180 Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

5-6. Mode Switch Settings For CC/CV Models

Mode

Output Control

Pulsed MIG

Panel Control

OM-203 034 Page 25