Door adjustment
<Adjusting refrigerator compartment doors>
•Common elements
First, check the installation condition.
1If the adjustment bolt is not in contact with the floor, lower the bolt, and adjust it so that the caster is slightly above the floor.
2 When the refrigerator is installed in the corner of the room, the bolt of the refrigerator may sink into the floor and cause the refrigerator to tilt. It is recommended to make adjustments by objects like boards beforehand.
3 When the refrigerator bolt is sunk into the floor, and it can be confirmed visually, prevent sinking by using objects like boards.
Note : The refrigerator weighs about 100kg, and is held by four bolts. How far each bolt sinks into the floor depends on factors such as floor pillars. Change in balance due to position of stored food (such as large or small amount of food stored in the door pockets) may also affect sinking.
<Adjusting ice making compartment and versa compartment doors>
Adjusting vertical space between doors | |
Adjusting doors horizontally |
|
Too much space | Not enough space |
A | B | B | B |
|
| ||
Problem |
| A | A |
|
|
|
| A>B (More space in outer side) 1 | A>B (Too much space between | A<B (Small space between the ice | ||
| Or | the ice making compartment and | making compartment and versa | ||
| A<B (More space in inner side) | versa compartment doors.) | compartment doors.)Misaligned | ||
|
| Misaligned versa compartment | versa compartment door 5 | ||
|
| door 3 | Misaligned ice making | ||
|
| Misaligned ice making | compartment door 6 | ||
|
| compartment door 4 |
|
| |
|
|
|
|
|
|
| 1 Place spacer set under the | 3 | Replace roller set of the right | 3 | Place roller set of the right and |
| outer roller of the tilted door |
| and left versa compartment |
| left versa compartment doors. |
| (ice making compartment door |
| doors. | a | To adjust about 0.5mm |
| in the above illustration) to | a | To adjust about 0.5mm |
| Replace with roller set A. |
| adjust position. |
| Replace with roller set C. | b | To make large adjustment |
Solution | tilted door | b | To make large adjustment | c | Replace with roller set B. |
| ice making compartment door. | To adjust about 0.5mm | |||
| 2 Place spacer |
| Replace with roller set D. | 6 | Replace lower roller set of the |
| set under the inner roller of the | 4 | Replace lower roller set of the |
| ice making compartment door. |
| (ice making compartment door | c | To adjust about 0.5mm |
| Replace with roller set C. |
| in the above illustration) to |
| Replace with roller set A. | d | To make large adjustment |
| adjust position. | d | To make large adjustment |
| Replace with roller set D. |
|
|
| Replace with roller set B. |
|
|
LH
Marking
right 0.5 [09] right 1.0 [11] left 0.5 [13] left 1.0 [15]
RH
Marking
right 0.5 [10] right 1.0 [12] left 0.5 [14] left 1.0 [16]
I dentifying roller sets (Marking)
| LH | RH |
|
|
|
Roller set A (0.5mm to the right) | 09 | 10 |
|
|
|
Roller set B (0.5mm to the right) | 11 | 12 |
|
|
|
Roller set C (0.5mm to the right) | 13 | 14 |
|
|
|
Roller set D (0.5mm to the right) | 15 | 16 |
|
|
|
40
