Setting the color temperature | Mitsubishi Electronics PD-5010

Setting the color temperature

Use this procedure to set color tone produced by the plasma display.

Example: Setting “LOW”

Press the MENU/ENTER button on the remote control to

display the MAIN MENU on the screen, then...

1.Use the ▲ and ▼ buttons to select “VIDEO SETTINGS”, then press the MENU/ENTER button. The “VIDEO SETTINGS” screen appears.

2.Use the ▲ and ▼ buttons to select “COLOR TEMP.”.

V I D E O S E T T I N G S

CONTRAST
CONTRAST
BRIGHTNESS
BRIGHTNESS
SHARPNESS
SHARPNESS
COLOR


TINT
TINT			R				G
PICTURE MODE			: MEMORY
			: MEDIUM
COLOR TEMP.			: MEDIUM
NR			: OFF
SEL.	ADJ.				RETURN
SEL.	ADJ.			EXIT	RETURN

3.Use the and buttons to select “LOW”.

The mode switches as follows when the and buttons are pressed:

HIGH MEDIUM LOW CUSTOM

* See page 23 to set “CUSTOM”.

4. Once the setting is completed...

Press the EXIT button to return to the main menu.

To delete the main menu, press the EXIT button once more.

Information

Setting the color temperature

HIGH	Whites appear more bluish
MEDIUM	Standard
LOW	Whites appear more reddish

Restoring the factory default settings

To restore the original factory settings, go back to the MAIN MENU. Select “FUNCTION,” and then select “RESET”. Note that this also restores other settings to the factory defaults.

COLOR TEMP. :LOW

*If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen reappears.

22

Image 28

Mitsubishi Electronics PD-5010 manual Setting the color temperature, Example Setting LOW, Once the setting is completed

Contents

Owner’s Guide Page Precautions Important Information To avoid damage and prolong operating life Contents Page Attachment Options for the PD-5010 Monitor Introduction Part Names and Function Rear View/ Terminal Board Remote Control Battery Installation and Replacement Using the wired remote control mode Installation Connecting Your PC or Macintosh Computer External Speaker Connections Pin Assignments and Signal Levels for 15 pin RGB Analog Basic Operations Information To set the off timer To cancel the off timerAfter the power is turned off with the off timer To check the remaining time Wide Operations Watching with a wide screen manual When Picture Size is set to OFF Information Supported resolutionPicture Size setting Watching computer images Operations in the Side-by-side mode PIP Screen OperationsShowing a couple of pictures on the screen at the same time Information Selecting the input signals to be displayed Operations in the Picture-in-picture modeAdjusting the ON-SCREEN Menu controls On Screen Menu Controls Menu Operations Main menu Sub menu Functions Default Picture Settings Menu Adjusting the pictureInformation Video Settings screen Adjusting the computer image Example Setting the Theater mode Information Types of picture modes Setting the color temperature Example Setting LOWOnce the setting is completed Information Setting the color temperature Example Adjusting the White Balance Adjusting the color to the desired qualityInformation Adjusting the white balance Reducing noise in the picture Example Setting NR-3Types of noise reduction Audio Settings Menu Adjusting the treble, bass and left/right balanceExample Adjusting the bass Information Sound settings menu Example Adjusting the vertical position in the normal mode Monitor Settings MenuInformation When Auto Picture is OFF Example Turning the on-screen menu mode off Setting the on-screen menuFunction Menu Adjusting the position of the menu display Example Adjusting the position of the menu displayTo adjust the position Information Adjusting the position of the menu display Setting the power management for computer images ExampleTurning the power management function onInformation Power management function Power management settings POWER/STANDBY indicator Setting the gray level for the sides of the screen Setting the picture to suit the movieExample Adjusting the Gray Level Example Setting the Cinema Mode to OFF Setting Monitorlink M-LINK ADJ Example SettingInformation When you adjust the M-LINK ADJ Example Setting PLE to Lock Setting the time for Inverse Peak Luminance Enhancement PLE Information Setting the time Setting the time for Screen WiperTo select on for the Working Time Resetting to the default values Speed Options Setting Menu Setting the allocation of the audio connectorsSetting the BNC connectors Example Setting Audio 1 to Video Setting a computer image to the correct RGB select screen Example Setting the RGB Select mode to MotionTo set the RGB select mode to Motion See page 55 for the details of the above settings Setting the picture size for RGB input signals Setting high definition images to the suitable screen sizeInformation HD Select modes Setting the language for the menus Example Setting the menu display to DeutschInformation Language settings Information Menu Setting the video signal format Example Setting the video signal format to 3.58 NtscInformation Video signal formats To select 3.58 Ntsc External Control ApplicationConnections Communication Format Command Reference List Power onPower OFF Input Switch Change Volume Gain Data Audio Mute OnAudio Mute Off Contrast Gain Data Color Gain Data Picture Mode SelectRED Gain Data NR Mode Set Green Gain DataBlue Gain Data Bass Gain Data Screen Mode Select Balance Gain Data22. V. Position Gain Data 23. H. Position Gain Data Phase Gain Data Auto Picture SelectClock Gain Data Menu Select Power MGT Select Cinema Mode SetMenu ADJ. Gain Data Gray Level Set Screen Wiper Set Inverse SetAudio Select Set RGB Select HD SelectPicture Size Select Language Select Color System Select Multi Screen Select Frequency Request Input Mode RequestHorizontal sync polarity Video ADJ Request Audio Select Request Failure Mode RequestModel Name Request Supported resolution Table of Signals SupportedComputer input signals supported by this system Page Troubleshooting Symptom Checks Remedy Specifications SignalsPage Mitsubishi Plasma Display Panel Limited Warranty