To operate projector power ON
|
|
| 2 • 9 |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| L | MAIN |
|
|
|
|
|
|
|
|
|
|
|
|
| |
| COMPUTER IN | R |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| VIDEO | 3•7•8 |
|
|
| 4 |
|
|
| AC IN |
|
|
| ||
|
| AUDIO IN VIDEO IN |
|
|
| |||
|
|
|
|
|
|
| ||
| COMPUTER OUT |
|
|
| COMPUTER VIDEO |
| ||
|
|
|
|
| MENU |
| ENTER |
|
3•7•8 | 4 |
| AUTO POSITION button | STILL | P in P | 16:9 |
| |
| POSITION | EXPAND KEYSTONE |
| |||||
|
|
| AUTO |
|
| AUTO POSITION | ||
|
| MUTE button |
|
|
| |||
|
|
|
| MUTE | - | + | button | |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| VOLUME |
| |
| COMPUTER | AUTO | MUTE |
|
|
|
| MUTE button |
| POSITION |
|
|
|
| |||
|
|
|
|
|
| |||
LAMP | VOLUME SOURCE |
|
|
|
|
|
|
|
TEMP | VIDEO | MENU | ENTER |
|
|
|
|
|
|
|
|
|
|
| |||
ENGLISH
1.Turn on the equipment connected to the projector.
2.Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.
3.Turn the projector on by pressing the POWER but- ton. The light source lamp starts warming up, even- tually turning completely on.
•When the light source lamp does not light up, wait until the LAMP indicator is turned off, then press the POWER button again.
•If the main power switch to the unit is turned off within two minutes of turning off the light source lamp, power will not be applied to the lamp for one minute when the next time the main unit power switch is turned on. When this happens, the indicator lamp will blink for one minute.
Indicator | LAMP | POWER | |
Condition | |||
|
| ||
- | Red | ||
When light source lamp is on | Green | Green | |
Light source lamp held off temporarily | - | Red |
Important:
•A darkened image may be seen right after pressing the POWER button due to warming up of this pro- jector. While warming up, no other commands can be accepted.
•After the power is turned on or the LAMP MODE is changed, the screen may flicker before the lamp op- eration becomes stable. This is due to the character- istics of the lamp, not a failure of the lamp.
•When the lamp indicator is blinking red, the lamp should be replaced. Replace the lamp. See pages 21 and 24.
•The picture might not be of optimum performance in extreme hot or cold conditions. (The projector is not malfunctioning.)
4.Select the desired external input source by using the COMPUTER or VIDEO button.
•Pressing the VIDEO button repeatedly will select VIDEO(1) and
•The COMPUTER or VIDEO button does not work when MENU is displayed. At this time, the prohibi- tion mark ( ) appeares on the screen.
•The projector automatically selects the appropriate signal format. The selected signal format is dis- played on the screen.
•When selecting the COMPUTER input, the image may flicker. Press the $ or % button to adjust the image.
•The brightness of the lamp will be STANDARD for 3 minutes regardless of the setting of the LAMP MODE when the lamp turns on.
5.Adjust the image size with the zoom ring by turn- ing it.
6.Adjust the focus with the focus ring by turning it.
focus ring | tele | zoom ring |
| ||
|
|
wide
near
far
EN – 13
