Load-Meter, Total Load by Phase | American Power Conversion 250 A

Load-Meter

Total Load by Phase

Total Load Summary

Power Factor

Sub-Feed Monitoring

Total Load by Phase

For each phase (L1, L2, L3), the following is displayed: kVA The apparent power provided, in kilovolt-amps. Iout The output RMS load current.

%LD The load as a percentage of the maximum allowable load.

Total Load Summary

For the total load supported, the following is displayed: kW The active power drawn by the load, in kilowatts. kVA The apparent power provided, in kilovolt-amps. Freq The frequency, in hertz.

PF The power factor, or the ratio between active power and apparent power (kW/kVA), that is being supplied to the load.

%LD The load as a percentage of the maximum allowable load.

Power Factor

The following power factor data is displayed for each phase (L1, L2, L3): kVA The apparent power provided, in kilovolt-amps.

kW The active power drawn by the load, in kilowatts.

PF The power factor, or the ratio between active power and apparent power (kW/kVA), that is being supplied to the load.

32	InfraStruXure Power Generation System

Image 42

American Power Conversion 250 A manual Load-Meter, Total Load by Phase, Total Load Summary, Power Factor

Contents

Operation Page Audience How to find updates to this manualAbout This Manual Companion manualsPage Contents Display Interface Communication Configuration Customizing and Updating the ATS Specifications Page Safety symbols used in this manual Cross-reference symbols used in this manualOverview Wire sizing Installation Total power off procedureOperating environment Page InfraStruXure Power Generation System Overview How the InfraStruXure Power Generation System Operates Generator start sequence Generator cool-down Open and closed transfers Fuel monitoring/runtime calculation Page Smart Distribution Panel with ATS Front view, door closed Front view, door open  The automatic operation Control panel is used to set Installation Manual for instructions ATS panel board, left side ATS panel board, right side Motorized switches ATS Component Details Automatic operation control panel User connection plate  When the EPO Arm/Test rocker is in the Test ATS monitoring unit ATS label kit Operation Automatic Operation Automatic Operation Problem-loss of automatic operation Emergency Manual Operation How to power the load from the generator Set the ATS Automatic Operation switch to Disable Emergency Manual Operation How to return to powering the load from utility Press Total Power Off Total Power Off Display Interface Top-level status screens Top-level menu screen Password-protected screens Navigating through screens Load-Meter Total Load by PhasePower Factor Total Load Summary ATS/Voltage ATS PositionS1-Utility S2-Generator ATS Setup ATS/Voltage Generator Generator Status Operating Settings Gen Output AdjustManufacturer Data Testing View Test LogRun/View Test Test Schedule Test Duration How a test occurs Reset Reset AllStats Alarm/Event Log AlarmsView Active Alarms Alarm Setup Fuel Alarm Limits Alarm BeeperClearing latched alarms Other Limits System/Network ConfigSystem Password Date/TimePage Firmware Updates Electrical ConfigFactory Defaults Reset 100% Fuel LevelPage InfraStruXure Manager ATS Management OptionsOverview Network management interfaces Configuring the InfraStruXure Manager Connect the ATS to the InfraStruXure Manager Configuring the ATS Network Management Interface Connect the ATS to your network Configuration overview TCP/IP configuration methodsDevice IP Configuration Wizard Bootp & Dhcp configuration Option 43 = 01 04 31 41 50 43 where Local access to the control console Remote access to the control console Control console Choose Network from the Control Console menu How to Access the ATS Network Management Interface Web interface Telnet and SSH Snmp FTP and SCP InfraStruXure Power Generation System Customizing and Updating the ATS How to connect contacts to the user interface board How to Connect an EPO Switch to the ATS EPO Test NC no Contact Closure-Normally Open Problem Action Safety warnings How to Allow Easy Access to the ATS Display Interface Output distribution circuit breakers available from APC Part Number Description Height on Panel Determine the configuration of the panel Circuit breaker adapter modules available from APC Allowed circuit breaker combinations Combination #1 Combination #6 Preparing the breakers for installation T1 three-pole breaker requires no additional preparation Parts and tools needed for installation procedures T1 three-pole breaker assembly Installing breakers on the ATS panel bus See also How to Download Firmware Updates From a local computer Electrical Physical Installation and Wiring 208V 480V AWG Environmental CompliancePage Appendix Custom Installations If Source 2 is a Second Utility InfraStruXure Power Generation System Index InfraStruXure Power Generation System InfraStruXure Power Generation System Page Page Page Radio Frequency Interference 990-1845C