ATS panel board, right side | American Power Conversion 250 A

Smart Distribution Panel with ATS

ATS panel board, right side

The Source 1 input switch accepts input wires from the utility (refer to the Electrical Installation Manual for connection instructions).

WARNING: Only a certified electrician should connect utility power to the ATS!

Behind this access panel are the Source 1 volt- sensing circuit board and the distribution panel volt-sensing circuit board. Use a Phillips or standard screwdriver to remove the panel.

The Source 1 current transformers monitor the input current of each incoming phase from the utility. The data gathered from these transformers is displayed on the Total Load by Phase screen, which is accessed through the Load Meter menu on the display interface.

Behind this access panel is the Source 2 volt- sensing circuit board. Use a Phillips or standard screwdriver to remove the panel.

The Source 2 control transformer outputs 120 VAC and 18 VAC to the Source 2 motorized switch after stepping down the 480 V or 208 V input.

The Source 2 fuse block regulates input to the Source 2 control transformer for subsequent powering of the Source 2 motorized switch.













14	InfraStruXure Power Generation System

Image 24

American Power Conversion 250 A manual ATS panel board, right side

Contents

Operation Page How to find updates to this manual About This ManualAudience Companion manualsPage Contents Display Interface Communication Configuration Customizing and Updating the ATS Specifications Page Safety symbols used in this manual Cross-reference symbols used in this manualOverview Wire sizing Installation Total power off procedureOperating environment Page InfraStruXure Power Generation System Overview How the InfraStruXure Power Generation System Operates Generator start sequence Generator cool-down Open and closed transfers Fuel monitoring/runtime calculation Page Smart Distribution Panel with ATS Front view, door closed Front view, door open  The automatic operation Control panel is used to set Installation Manual for instructions ATS panel board, left side ATS panel board, right side Motorized switches ATS Component Details Automatic operation control panel User connection plate  When the EPO Arm/Test rocker is in the Test ATS monitoring unit ATS label kit Operation Automatic Operation Automatic Operation Problem-loss of automatic operation Emergency Manual Operation How to power the load from the generator Set the ATS Automatic Operation switch to Disable Emergency Manual Operation How to return to powering the load from utility Press Total Power Off Total Power Off Display Interface Top-level status screens Top-level menu screen Password-protected screens Navigating through screens Total Load by Phase Power FactorLoad-Meter Total Load Summary ATS/Voltage ATS PositionS1-Utility S2-Generator ATS Setup ATS/Voltage Generator Generator Status Operating Settings Gen Output AdjustManufacturer Data Testing View Test LogRun/View Test Test Schedule Test Duration How a test occurs Reset Reset AllStats Alarms View Active AlarmsAlarm/Event Log Alarm Setup Alarm Beeper Clearing latched alarmsFuel Alarm Limits Other Limits Config System PasswordSystem/Network Date/TimePage Electrical Config Factory DefaultsFirmware Updates Reset 100% Fuel LevelPage ATS Management Options OverviewInfraStruXure Manager Network management interfaces Configuring the InfraStruXure Manager Connect the ATS to the InfraStruXure Manager Configuring the ATS Network Management Interface Connect the ATS to your network Configuration overview TCP/IP configuration methodsDevice IP Configuration Wizard Bootp & Dhcp configuration Option 43 = 01 04 31 41 50 43 where Local access to the control console Remote access to the control console Control console Choose Network from the Control Console menu How to Access the ATS Network Management Interface Web interface Telnet and SSH Snmp FTP and SCP InfraStruXure Power Generation System Customizing and Updating the ATS How to connect contacts to the user interface board How to Connect an EPO Switch to the ATS EPO Test NC no Contact Closure-Normally Open Problem Action Safety warnings How to Allow Easy Access to the ATS Display Interface Output distribution circuit breakers available from APC Part Number Description Height on Panel Determine the configuration of the panel Circuit breaker adapter modules available from APC Allowed circuit breaker combinations Combination #1 Combination #6 Preparing the breakers for installation T1 three-pole breaker requires no additional preparation Parts and tools needed for installation procedures T1 three-pole breaker assembly Installing breakers on the ATS panel bus See also How to Download Firmware Updates From a local computer Electrical Physical Installation and Wiring 208V 480V AWG Environmental CompliancePage Appendix Custom Installations If Source 2 is a Second Utility InfraStruXure Power Generation System Index InfraStruXure Power Generation System InfraStruXure Power Generation System Page Page Page Radio Frequency Interference 990-1845C