4. TV Operation and Features 27
Note: Tooperateotheraudio/videodevices:
• SeeAppendixD,“ProgrammingtheRemote
Cont rol.”
• Seechapter6,“NetCommand,”forNetCommand
IR“Learning”ofdevicekeys.
• ForHDMIdevicescompatiblewiththeTV’s
NetCommandforHDMIfeature,seebelow.
ChannelView™ Channel Listings
ChannelViewshowsmemorizedchannelson
ANT 1
and
ANT 2
.Itdisplayschannelnamesandprogram
informationassentbybroadcastersoryourlocalcable
serviceproviderandmaybeincomplete
.
Noprogram
informationisdisplayedforanalogchannels.Ananalog
channelnameisdisplayedonlyifyouassignedaname
intheSetup > Editmenu.
T
oreceiveChannelViewupdates,settheEnergyMode
toFast Power OnandleavetheTVpoweredofffora
whileeachday.

Using ChannelView

Feature Press Key
SeeChannelViewlistings
fromANT 1orANT 2.
Press
GUIDE.
CloseChannelView Press
GUIDE
or
EXI T.
Scanchannelsonebyone. Pressandhold or .
Scanchannelsquickly.
Pressandhold
PAGE
/
.
Jumptolistingsforaspe-
cificchannel.
1. Enterthechannel
number(seenumbers
inupperleft.
2. Press
ENTER
.
Seemoreoftheprogram
description.
Press
INFO
.
Movenavigationtothe
programguide.
Press .
Movenavigationtothe
channelguide.
Press .
Tunetothehighlighted
channel.
Press
ENTER
.

Record/Playback Keys

Useanyofthesemethodstoenabletherecordingand
playbackcommands:
• ProgramtheremotecontrolforyourDVR,VCR,or
DVDplayer/recorderandsettheslideswitchto
VCR
,
DVD
,
CABLE
,or
SAT
.
• Yand734seriesTVs:PerformNetCommandIR
“learning”forthedevice.
• CheckHDMIdevicesforcompatibilitywiththeTV’s
NetCommandforHDMIfeature(seebelow).
23. (
PAUSE
): PausesaVCR,DVR,orDVD.See
aboveforuseduringTVviewing.
24. (
PLAY
):PlaysaVCR, DVR, orDVD.
25. (
RECORD
):
RecordswithaVCRorDVR.
26. (
STOP
):StopsplayofaVCR, DVR, orDVD.
27. (
REVERSE
): RewindsaVCR.Reversescansa
DVRorDVD.
28. (
FORWARD
):FastforwardsaVCR.Forwardscans
aDVRorDVD.
Remote Control, continued

Care of the Remote Control

• Useonlyalkalinebatteries.
• Bewithin20feetoftheequipment.
• Donotpresstwoormorebuttonsatthesametime
unlessinstructedtodoso.
• Donotallowunittogetwetorbecomeheated.
• Avoiddroppingonhardsurfaces.
• Donotuseharshchemicalstoclean.Useonlya
soft,lightlymoistenedcloth.
• Donotmixoldandnewbatteries.

Resetting the Remote Control

Iftheslideswitchissetto
TV
andtheTVdoesnot
respondproperly,resettheremotecontrol.
1. Pressandhold
POWER
forseveralsecondsuntilthe
buttonblinkstwiceandgoesoff.
2. Releasethe
POWER
button.
3. Presskeys
0 0 9 3 5
andthe
POWER
buttonwillblink
twicewhenyoufinishenteringthecode.While
enteringthecode,pauseforamomentbetween
eachkeypresstoensureitisrecognized.

Low-Battery Indicator

Ifyoupressakeyandthe
POWER
keyblinksfivetimes,
replacetheremotecontrol’sbatteries.

NetCommand for HDMI Devices

TheTV’sremotemayoperatesomefunctionsof
compatibleHDMIdevicesabletoreceivecommands
throughtheHDMIcable.Testyourequipmentwiththe
TV’sremotetofindoutwhichcommandsaresup-
ported.Seebelowforcommandsthatmaybeavail-
able,dependingontheindividualdevice.
Press
PLAY
onthedeviceitselfto:
• TurnontheTVifnotalreadyon
• Switchtothedevice(noneedtodisplaytheInput
Selectionmenu)
• Beginplayofthedevice
VCR,DVD,andDVRfunctionsthatmaybeavailable:
Record/
Playback
Menu
Navigation Channel Tuning Other
CH
/
GUIDE
ENTER
Digits
0–9
,
—
CANCEL F1
(content)
—
CANCEL
(tocancel)
ENTER MENU