Manuals / Monessen Hearth / Household Appliance / Indoor Fireplace

Monessen Hearth DEB30, DEB20 manual Replacement Parts, Burner Assembly

Models: DEB20 DEB30

1 40

Download 40 pages 19.41 Kb

Page 35

Image 35

REPLACEMENT PARTS

BURNER ASSEMBLY

			3
		5 (Manual)	11
			11
10	6	12	8
10

5 (Milli-Volt)

WARNING

Failure to position the parts in accordance with these diagrams or failure to use only parts speciﬁcally approved with this appliance may result in property damage or personal injury.

44D0060

Page 35

Image 35

Monessen Hearth DEB30, DEB20 manual Replacement Parts, Burner Assembly

Contents

WARNINGS INSTALLATION AND OPERATING INSTRUCTIONSCONTENTS IMPORTANT SAFETY INFORMATION Continued from page IMPORTANT SAFETY INFORMATIONMAKE SURE YOU HAVE RECEIVED ALL PARTS GETTING STARTEDWHAT YOU WILL NEED FOR INSTALLATION Manual Pressure PRODUCT FEATURES AND SPECIFICATIONSManual Pressure Milli-VoltPressureAll gas to the gas logs is shut off at the valve PRODUCT FEATURES AND SPECIFICATIONSAll gas to the gas logs is shut off at the valve Valve position to light/maintain a standing pilotCODES GENERAL INSTALLATION INFORMATIONAmerican National Standards Institute, Inc National Fire Protection Association, IncGENERAL INSTALLATION INFORMATION FIREPLACE AND HEARTH DIMENSIONS Minimum Depth of Fireplace/Firebox Height of RestrictionFigure 4 - Sidewall and Ceiling Clearances CLEARANCES AND HEIGHT REQUIREMENTSFigure 5 - Measuring Heat Resistant Material CLEARANCES and HEIGHT REQUIREMENTSHood CLEARANCES and HEIGHT REQUIREMENTS8 or More of Heat ResistanCLEARANCES AND HEIGHT REQUIRMENTS maximum of 10 at a minimum of 28 above the CLEARANCES AND HEIGHT REQUIRMENTSThis Distance May Now Be Less than FLOOR CLEARANCEHeater in Fireplace or Firebox Combustible Material 5 MinimumFIREPLACE PREPARATION PLACING AND SECURING APPLIANCE INSTALLING VENTED APPLICATIONSFigure 15 - Gas Connection CONNECTING THE GASMILLI-VOLTCONTROL Figure CHECKING GAS PRESSUREMANUAL CONTROL Figure errors can cause improper and ELECTRICAL WIRING MILLI-VOLTLabel all wires prior to disconnection when servicing controls. WiringSETTIN ELECTRICAL WIRING MILLI-VOLTCONNECTING REMOTE RECEIVER INSTALLING T-STATSENSOR OPTION SOLD SEPARATELYTH TP/TH Wiring Harnesses ELECTRICAL WIRING MILLI-VOLTWiring Harnesses Screw Figure 22 - Installing T-StatSensor to DEB BaseA.COMPLETE MILLI-VOLTSYSTEM CHECK ELECTRICAL WIRING MILLI-VOLTOPERATION OF THERMOSTAT SENSOR CHECKING SYSTEM OPERATIONINSTALLING LOGS ON GRATE See Figures 25 and LOG PLACEMENTMILLI-VOLTCONTROL FLAME APPEARANCEPLACING THE DECORATIVE ROCK CHECKING THE PILOT FLAMEOPERATING INSTRUCTIONS CHECKING THE BURNER FLAMEOPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGheater when the control knob has been MANUAL CONTROL LIGHTING INSTRUCTIONSTO TURN OFF GAS TO HEATER Wait 30 seconds before readjusting theOPERATING INSTRUCTIONS MILLI-VOLTCONTROL LIGHTING INSTRUCTIONSTO TURN OFF GAS TO HEATER MATCH LIGHTING INSTRUCTIONS OPERATING INSTRUCTIONS AND CLEANING AND SERVICINGWARNING WARNING TROUBLESHOOTINGGas odor even when control When ignitor button is pressedODS/pilot lights, but flame TROUBLESHOOTINGgoes out when control knob is noise when burner is litBURNER ASSEMBLY REPLACEMENT PARTSREPLACEMENT PARTS LIST 6 3 2 1 4 5 DEB24/DEB30 REPLACEMENT PARTS LISTLOGS CARBON MONOXIDE DETECTOR REQUIREMENTS SPECIAL REQUIREMENTSNOTE REGARDING VENTED PRODUCTS NOTE REGARDING VENT FREE PRODUCTSSPECIAL REQUIREMENTS CONTINUED MONESSEN HEARTH SYSTEMS LIMITED LIFETIME WARRANTY POLICY