Manuals / Motorola / Computer Equipment / Computer Hardware

Motorola PrPMC800/800ET Processor PMC Module, PRPMC800A/IH5 manual Select the identifier. Default =

Models: PRPMC800A/IH5 PrPMC800/800ET Processor PMC Module

1 92

Download 92 pages 1.03 Kb

Page 71

6 Modifying the Environment

Probe System for Supported I/O Controllers [Y/N] = Y?

YAccesses will be made to the appropriate system buses (e.g., VMEbus, local MPU bus) to determine the presence of supported controllers. (Default)

NAccesses will not be made to the VMEbus to determine the presence of supported controllers.

Auto-Initialize of NVRAM Header Enable [Y/N] = Y?

YNVRAM (PReP partition) header space will be initialized automatically during board initialization, but only if the PReP partition fails a sanity check. (Default)

NNVRAM header space will not be initialized automatically during board initialization.

Network PReP-Boot Mode Enable [Y/N] = N?

YEnable PReP-style network booting (same boot image from a network interface as from a mass storage device).

NDo not enable PReP-style network booting. (Default)

SCSI Bus Reset on Debugger Startup [Y/N] = N?

YLocal SCSI bus is reset on debugger setup.

NLocal SCSI bus is not reset on debugger setup. (Default)

Primary SCSI Bus Negotiations Type [A/S/N] = A?

AAsynchronous SCSI bus negotiation. (Default)

SSynchronous SCSI bus negotiation.

NNone.

Primary SCSI Data Bus Width [W/N] = N?

WWide SCSI (16-bit bus).

NNarrow SCSI (8-bit bus). (Default)

Secondary SCSI identifier = 07?

Select the identifier. (Default = 07.)

NVRAM Bootlist (GEV.fw-boot-path) Boot Enable [Y/N] = N?

YGive boot priority to devices defined in the fw-boot-pathglobal environment variable (GEV).

NDo not give boot priority to devices listed in the fw-boot-pathGEV. (Default)

Note When enabled, the GEV (Global Environment Variable) boot takes priority over all other boots, including Autoboot and Network Boot.

PrPMC800/800ET Processor PMC Module Installation and Use (PrPMC800A/IH5)

51

Image 71

Motorola PrPMC800/800ET Processor PMC Module, PRPMC800A/IH5 manual Select the identifier. Default =

Contents

Installation and Use Page Keep Away From Live Circuits Inside the Equipment Use Caution When Exposing or Handling a CRTGround the Instrument Do Not Operate in an Explosive AtmosphereFlammability Limited and Restricted Rights Legend Page Contents Connector Pin Assignments Modifying the Environment Contents List of Figures List of Figures List of Tables J2 Harrier Power-Up Configuration Header Pin AssignmentsList of Tables 2MB PrPMC800/800ET Models/ConfigurationsAbout This Manual 1MBAbout This Manual PRPMC800A/IH2 PRPMC800A/IH5PRPMC800A/IH4 PRPMC800A/IH3Overview of Contents Conventions Used in This Manual About This Manual PrPMC800/800ET Description Preparation and InstallationIntroduction System Enclosure Monarch and Non-Monarch PrPMCsCarrier Board Requirements What you need to do Refer to Overview of Start-Up ProceduresStart-Up Overview Preparing the Hardware PrPMC800/800ET ConfigurationUnpacking the Hardware Jumper On Jumper Off Harrier Power-Up Configuration HeaderJ2 Harrier Power-Up Configuration Header Pin Assignments PrPMC800/800ET Headers, Connectors and Components Installation of PrPMC800/800ET on a VME or CompactPCI Board InstallationESD Precautions Installing a PrPMC800/800ET on a VMEmodule Operating Instructions Applying PowerOperating Instructions Status IndicatorsPrPMC800/800ET Debug Debug Serial PortEthernet Port Adapter Cable Page Functional Description FeaturesPrPMC800/800ET Features Feature DescriptionSrom General DescriptionPrPMC800/800ET Block Diagram Block DiagramHarrier System Memory Controller / PCI Host Bridge Asic ProcessorL2 Cache Option Power Register Bit Bus Signal Setting Harrier Power-Up ConfigurationHarrier Power-Up Configuration Settings Harrier Select Default Function DescriptionXCSR.XPAT0.DW XCSR.GCSR.PUSTXAD M66ENXCSR.XPAT2.DW ArbitrationFlash Memory XCSR.XPAT1.DWOnboard Sdram ECC MemoryOnboard Bank a Flash Optional Bank B FlashMiscellaneous Control and Status TimersBit Timers 10BaseT/100BaseTX Ethernet ChannelClock Generator Watchdog TimersInterrupt Routing and Generation Asynchronous Serial PortReset Source Type Module Reset PrPMC Resetoutl Active PrPMC800/800ET Power SuppliesModule Reset Logic Reset Source FunctionsPCI Interface PrPMC800/800ET Reset Block DiagramIDSELB, REQB#, and GNTB# Signals PRESENT# SignalMONARCH# Signal INTA#-INTD# SignalsDebug Header Eready SignalPCI Signaling Voltage Level ABORT# and RESET# SignalsMemory Maps Page PMC Connector P11 Pin Assignments Connector Pin AssignmentsPCI Mezzanine Card PMC Connectors GND VIO SDONE# SBO# PAR GND VIOPMC Connector P12 Pin Assignments PAR64 PMC Connector P13 Pin AssignmentsP14 PMC Connector P14 Pin AssignmentsSignal Description for P14 TXP TXN RXP RXN Lanterma Lantermb Ethernet Adapter ConnectorJ3 Ethernet Adapter Connector Pin Assignments J1 Debug Header Pin AssignmentsRsvd Signal Description for J1Shunt On Shunt Off PrPMC Cable-001 Termination Cputrstl Pullup Cputck Cputms Sresetl Cpurstl Ckstpol GNDDebug Serial Port Cable PPCBug Basics PPCBugOverview PPCBug Implementation Memory RequirementsMPU, Hardware, and Firmware Initialization Using PPCBug Command Description Debugger CommandsDebugger Commands IOC GevinitGevshow IdleNopa PbootReset NpingTest Group Description Diagnostic TestsDiagnostic Test Groups Mpic IsabrdgeL2CACHE MaskPage Modifying the Environment Cnfg Configure Board Information BlockENV Set Environment Configuring the PPCBug ParametersSelect the identifier. Default = Default = $00 Auto Boot Abort Delay = 7? Default Starting Address is $00000000 ROM First Access Length 0 31 = 10? Serial Startup Code Master Enable Y/N=N? Electrical Characteristics SpecificationsSpecifications Mechanical CharacteristicsEMC Compliance Environmental CharacteristicsCharacteristics Specifications Thermally Significant Components Thermal ValidationThermal Validation Table B-1. Thermally Significant ComponentsFigure B-1. Thermally Significant Components Primary Side Preparation Component Temperature MeasurementMeasuring Local Air Temperature Measuring Junction TemperatureMeasuring Case Temperature Figure B-4. Mounting a Thermocouple Under a Heatsink Table C-1. Embedded Communications Computing Documents Related DocumentationEmbedded Communications Computing Documents Table C-2. Manufacturers’ Documents Manufacturers’ DocumentsDocument Title and Source Publication Number Related SpecificationsTable C-3. Related Specifications Page CPU IndexFail LED IndexIDSELB, REQB#, GNTB# 25 INTA#-INTD# Xix