Bumper, Hiller/Furrower, ROW Marker | MTD 12212, 12211 instruction

Section 5: Maintenance

WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on elec- tric start models. Failure to follow these instructions can result in serious personal injury or property damage.

TILLER ATTACHMENTS

The attachments listed below are available for your tiller. The information is the most current at the time this manual was printed. Contact your authorized dealer or the factory for current information.

BUMPER

The tubular steel bumper helps to protect the engine from damage.

HILLER/FURROWER

The furrower blade attaches to the back of the depth regulator assembly and is used to create rows, trenches and ditches up to 8" deep, depending on soil conditions. The two hiller wings attach to the sides of the furrower blade and are used to make hilled rows and raised bed gardens.

ROW MARKER

The row marker attaches to the hiller/furrower attachment and is used to scratch lines in the seedbed for laying out furrows, trenches, raised beds, etc. (eliminates the need for stakes, string and measuring tape). The row marker is adjustable in length from 28" to 49-3/4", allowing you to vary the width of the marked rows as required.

31

Image 31

MTD 12212, 12211 owner manual Bumper, Hiller/Furrower, ROW Marker

Contents

Recoil Start Model shown 7HP Pony REAR-TINE Tiller See Back Cover for Customer Service information Operation Repairs, adjustments or inspectionsTraining Preparation Keep children and pets away Maintenance and StorageUse slower engine speeds Decals Operating SymbolsTo Avoid Serious Injury Attach Handlebars Hardware BAG Parts ListIntroduction Inspect Unit Attach Forward Clutch Control Cable Attach Reverse Clutch Control Cable Check Transmission Gear OIL Level ADD Motor OIL to Engine Check AIR Pressure in Tires Attach Wheel Gear LeverCheck Hardware for Tightness Battery Activation and Charging Electric Start Assembly Steps Install Battery Attach Battery Cables and Vent Tube Keyswitch Connect Wiring Harness To Operate the Forward Clutch Control Engine ControlsForward Clutch Control Wheel Gear Lever Depth Regulator Handlebar Height AdjustmentTo Adjust the Handlebar Height Reverse Clutch Control Stop Stops the engine on recoil start models only Electric Start Keyswitch Electric Start ModelEngine Controls Engine Throttle Control Lever BREAK-IN Operation PRE-START ChecklistStarting and Stopping Engine Release all controls on the tiller Operating the TillerStarting the Engine Stopping the Engine Stopping the Tiller and Engine Turning the Tiller AroundFor forward motion of the wheels and tines For reverse motion of the wheels and tines Avoid making footprints Let the tiller do the workTilling depths Avoid tilling soggy, wet soil Tilling up and down slopes Tilling across slopes without using terracesClearing the tines Tilling on slopes Loading and Unloading the Tiller Power Composting Every Required Maintenance ScheduleProcedure Tiller Lubrication Check for OIL Leaks Transmission Gear OIL ServiceCheck Hardware Check Tire Pressure CARBURETOR/GOVERNOR Control Adjustments Engine CleaningEngine OIL Service AIR Cleaner Service OFF Season Storage Wheel Gear Cable AdjustmentBolo Tines Checking and Adjusting Tension on Clutch Belts Checking and Adjusting Forward Clutch Belt TensionCutting Edge Tine More Belt Tension Checking and Adjusting Reverse Clutch Belt Tension Removing Forward Clutch Belt Installing Forward Clutch Belt Removing Reverse Clutch Belt Installing Reverse Clutch Belt Battery Removal and Installation Battery MaintenanceBattery Care in Service Battery Storage HILLER/FURROWER BumperROW Marker Problem Possible Cause Correction Troubleshooting Part Description Models 12211QTY See page 36, Ref 47, for attach Ment screw Parts List ENGINE, Support BRACKETS, PULLEYS, BELTS, Belt Cover 1917326 Part Description QTY Main Drive Shaft Input Pinion Shaft & Gear Assembly Wheel SHAFT, Eccentric Shaft and Tiller Shaft Assemblies Thicker than standard tines Bolo TINES, Wheels Electric Start Assembly 1918831001 Battery Bracket Bumper Attachment ROW Marker Attachment2322 Description QTY ROW Marker Attachment & Bumper AttachmentRow Marker Attachment option Bumper HILLER/FURROWER Attachment Page Owner Registration Card Warranty ServiceReplacement Parts Engine Service and Repair