Napco Security Technologies GEM-P9600 Central Station Receiver 1 Format, Enter User Codes

Programming the GEM-P816 & GEM-P1632

13 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

Central Station Receiver 1 Format

From the table below, enter the central station's receiver format. Use number buttons 1through 9. NOTE: Press G0for a zero and 0

for a blank space (•). Press G1through G4for letters B–E,

respectively. Press Jto save. Press NEXT (E) button to proceed.

NOTE: Central Station Receiver 2 and 3 Formats can only be entered in Direct Address Programming. See CS Receiver Options.

DATA	CS RECEIVER 1 FORMAT
ENTRY
•(blank)	Ademco Slow, Silent Knight Slow
2	Radionics Fast
3	Silent Knight Fast
4	Radionics, CD, Franklin Slow

DATA	CS RECEIVER 1 FORMAT
ENTRY
5	Universal High Speed
B	SIA
C	Ademco Point ID
E	Pager

14 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

User # User Code

Enter User Codes

For default program, enter up to 32 User Codes, with Area 1 and Area 2 Options.Press the (A) button once to set the cursor to the User Code.

Use the number buttons 0 through 9 to enter the User Number, followed by a User Code of up to 6 digits. Enter G0for a blank.

NOTE: If “Enable Global Ambush Code”(Address 0720) is enabled and “Global Ambush Code” (Address 1054) is left blank(•),do not program the first two digits of ANY User Code as '99'.

		NOTE: When entering the Area 1 and
		Area 2 options, press G0for a
		ten. Enter 0for a blank.
Area 1	Area2
Options	Options

USER AREA OPTIONS - Select the desired Area Options (Area 1 and Area 2) from the table below.

DATA ENTRIES		OPTION ENABLED
L	R		EXPLANATION
blank(•)	blank(•)	Disabled	User Code not active in this area.
blank(•)	1	Arm/Disarm	Allows User Code to arm/disarm this area.
blank(•)	2	Arm Only	Prevents User Code from disarming this area.
blank(•)	3	Service	A Service Code has restricted arm/disarm rights; if an area is armed with a Service Code, the area can be disarmed
			with any valid User Code, including a Service Code. If the area is armed with OTHER than a Service Code, it CANNOT
			be disarmed with a Service Code.
blank(•)	4	Access	This is normally used to activate a door striker while an area is disarmed. Also program “Access Control on PGM2
			Output” (Address 0719) and “PGM2 Output Access Control Timeout” (Address 0711).
blank(•)	Add 8	* User Program	User Program Option is enabled for Keypad 1 only, wherever it is connected (Area 1 or Area 2).

∙Press Jto save. To proceed to the next User Code, press the Abutton to set the cursor to the User Number and change it using the number buttons.

∙If the programmed code was less than 6 digits, enter blanks G0for the remaining digits.

Example: Program a code of “2222” for user 02, with area 1 options of “Arm/Disarm” and “User Program”:

Enter 02for the user number, 2222 G0 G0for a user code, G09“(blank) 9” for area 1 options andG0G0“(blank) (blank)” for area 2 options.

CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above and press Jto save. Similarly, to cancel a code, blank out each number of the code press Jto save.

7