W415-0171/D/01.06.04

5

CARE OF GLASS, ENAMELLED AND PLATED PARTS

Do not use abrasive cleaners to clean these parts. Buff lightly with a clean dry cloth. Porcelain enamelled compo- nents must be handled with care. The baked-on finish is glasslike. If struck, it will chip! Touch-up paint is available through your Napoleon dealer.

The glass is 3/16" ceramic glass available from your Na- poleon dealer. DO NOT SUBSTITUTE MATERIALS. Clean the glass after the first 10 hours of operation with a recom- mended gas fireplace glass cleaner. Thereafter clean as required. DO NOT CLEAN GLASS WHEN HOT! If the glass is not kept clean permanent discolouration and / or blem- ishes may result.

INSTALLATION

FIGURE2

Clean out the ashes from the inside of the woodburning fireplace. Make sure that the chimney and woodburning fireplace are in clean and sound condition. Do not remove bricks or mortar from the masonry fireplace. If necessary have any repair work done by a qualified person before installing the insert. Remove the existing fireplace damper or lock into an open position. Line the chimney with a 4 inch diameter approved liner. Pack insulation around the liner in the damper area to prevent air flow from entering the chimney. Chimney installation must conform to both national and local code requirements. The liner must be continuous from the fireplace to the chimney cap.

FIGURE3

Remove the securing screw from the front of the dilution plate. Push the dilution hood out of its securing clip and attach the liner using 3 screws equally spaced. Move the insert into the centre of the woodburning fireplace making sure that the dilution draft hood inserts back into its secur- ing clip. Level using the four levelling screws located front and back on either side of the fireplace base.

FIGURE4

Levelling the insert will eliminate rocking or excessive noise when the fan is in operation. Replace the securing screw to the front of the dilution plate.

FIGURE5

Install rigid black pipe, a flex connector, if local codes per- mit, or 1/2" type L, copper tubing with a 3/8" to 1/2" adapter and a shut off valve to the fireplace. Seal and tighten se- curely. The adapter will be required between the gas valve and the copper tubing or flex connector.

Do not damage or kink flex connector!

Check for gas leaks by brushing on a soap and water solution.

Do not use open flame!

An on/off switch has been included and can be located at the lower right, behind the louvre access door or at the right side trim.

For ease of accessibility, this switch may be replaced with a wall switch or substituted with a millivolt thermostat that may be installed in a convenient location on any wall. Route 2-strand (solid core) millivolt wire through the electrical hole located at the bottom right side of the unit. The rec- ommended maximum lead length depends on wire size:

WIRE SIZE

MAX. LENGTH

14gauge

100 feet

16gauge

60 feet

18gauge

40 feet

1

2

3

FIGURE6

Attach the two leads to terminals 1 and 3 located on the gas valve.

Do not connect either the wall switch or the gas valve to electricity (110 volts or 24 volts).

Page 4 Page 6
Page 5
Image 5
Napoleon Fireplaces GI3016-P, GI3016-N manual Installation, Care of GLASS, Enamelled and Plated Parts
Page 4 Page 6

GI3016-P, GI3016-N specifications

Napoleon Fireplaces GI3016-N and GI3016-P are modern gas fireplaces designed to enhance the warmth and ambiance of any living space. With their striking aesthetics and efficient heating capabilities, these units serve as both functional and decorative focal points in homes.

One of the most prominent features of the GI3016-N and GI3016-P is their sleek and contemporary design. The clean lines and elegant glass front allow for an unobstructed view of the dancing flames, creating an inviting atmosphere. Available in two configurations, the GI3016-N is a natural gas model, while the GI3016-P offers the convenience of propane. This flexibility makes them suitable for a variety of installations and user preferences.

These fireplaces boast advanced heating technologies, ensuring they provide maximum warmth with minimal energy consumption. The multi-function remote control allows users to adjust the flame height and control the fan speed, giving them complete command over both comfort and ambiance. The efficient heat output is further complemented by a variable-speed blower, which circulates warm air throughout the room evenly and effectively.

Efficiency is a hallmark of the GI3016-N and GI3016-P. With high-efficiency ratings, these fireplaces are designed to maximize heat while minimizing gas usage. The impressive heating capability can warm spaces of up to 1,500 square feet, making them ideal for residential settings. Additionally, the technology used in these units ensures low emissions, promoting a cleaner burning experience.

Safety is also a key consideration in the design of Napoleon Fireplaces. The units come equipped with an automatic shut-off feature and a safety screen that protects users from accidental burns. This is particularly beneficial for households with pets and children.

In terms of installation, the GI3016-N and GI3016-P are versatile, allowing for venting through the roof or side wall, which provides flexibility in positioning within the home.

Overall, Napoleon Fireplaces GI3016-N and GI3016-P exemplify quality craftsmanship combined with innovative technologies, making them a perfect addition to modern homes. With their stylish designs, efficient heating capacity, and thoughtful safety features, these fireplaces deliver both comfort and elegance, enhancing the overall living experience.
Top Page Image Contents