Napoleon Fireplaces GI3016-N, GI3016-P manual Operation / Maintenance

10

OPERATION / MAINTENANCE

OPERATING INSTRUCTIONS FRESH AIR DAMPER SYSTEM

When lit for the first time, the stove will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing of the logs and the "burn-in" of inter- nal paints and lubricants used in the manufacturing proc- ess and will not occur again.

Simply open a window to sufficiently ventilate the room. After extended periods of non-operation such as following a vacation or a warm weather season, the fireplace may emit a slight odour for a few hours. This is caused by dust particles in the heat exchanger burning off. Open a window to sufficiently ventilate the room.

If your masonry fireplace is equipped with a fresh air inlet in the floor of the firebrick chamber, the insert is able to take outside air directly into the unit through an opening in its base thereby eliminating the need to use preheated room air for combustion. The flow of air may be adjusted through the use of a damper located below the louvre ac- cess door. The damper should be kept closed (pushed all the way in) when the unit is not in operation or if no outside air is available. The damper is fully open when pulled for- ward (one inch from the closed position).

FIGURE 22

Never obstruct the flow of combustion or

ventilation air.

FOR YOUR SAFETY READ BEFORE LIGHTING:

AThis stove has a pilot which must be lit by hand while following these instructions exactly.

BBefore lighting, smell all around the fireplace area for gas and next to the floor because some gas is heavier than air and will settle on the floor.

CUse only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it.

Call a qualified service technician. Force or attempted repair may result in a fire or explosion.

DDo not use this insert if any part has been under water. Immediately call a qualified service technician to inspect the unit and replace any part of the control system and any gas control touched by water.

WHAT TO DO IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire de- partment.

LIGHTING INSTRUCTIONS

1.Stop! Read all the safety information above. When lighting and relighting, the gas knob cannot be turned from "pilot" to "off" unless the knob is depressed.

2.Turn off all electrical power to the stove.

3.Turn the gas knob clockwise to off.

4.Wait 5 minutes for any gas in the combustion cham- ber to escape. Continue to the next step if you do NOT smell any gas. If you smell gas, STOP! and follow the instructions in "What to do if You Smell Gas" listed above.

5.If the unit is equipped with a flame adjustment valve, turn clockwise to off.

6.Locate the pilot situated in front of the rear log.

7.Turn the gas knob counter-clockwise to "pi- lot" position.

8.Depress and hold the gas knob while lighting the pilot with the push button igniter. Keep the knob fully de- pressed for one (1) minute, then release. If the pilot does not continue to burn, repeat steps 3 through 7.

9.With the pilot lit, turn the gas knob counter-clock-

wise to "on" position.

10.If your insert is equipped with a flame adjustment valve, push and turn the knob to "high".

11.If your insert is equipped with a remote "on-off" switch,

the main burner may not come on when you turn the gas valve to "on" or "high". The remote switch must be in the

"on" position as well to ignite the main burner. THERMOPIL

12.Turn on all electrical power to the insert.

PILOT BURNER

GAS VALVE ELECTRODE

TO TURN OFF GAS

1. Turn off all electrical power to the unit if service is	2. Push in gas control knob slightly and turn clock-
to be performed.	wise to off.	Do not force.

W415-0171/D/01.06.04