First Edition, Sept
NI WAP-3701/3711 User’s Manual
NI WAP-3701/3711 User’s Manual
Copyright Notice
Trademarks
Disclaimer
Table of Contents
Appendix D
Technical Support and Professional Services
Appendix C
Regulatory Statement
Introduction
‰ Overview ‰ Package Checklist ‰ Product Features
‰ Product Specifications
Overview
Package Checklist
Product Features
Product Specifications
Introduction
Software Features
Power
NI WAP-3701/3711 User’s Manual
‰ Confirming the Settings of the AP and Client Computers
Getting Started
‰ First-Time Installation and Configuration
‰ Deploying the Access Point AP ‰ Setting up Client Computers
Step 4 Use the web-based manager to configure the NI WAP-3701/3711
First-Time Installation and Configuration
Step 1 Select the Power Source
Step 3 Set up the computer’s IP address
Step 5 Select the Operational Mode for NI WAP-3701/3711
NI WAP-3701/3711 User’s Manual
Getting Started
instructions
Getting Started
Step 6 Configure the NI WAP-3701/3711’s IEEE 802.11 settings
Step 7 Review and Apply Settings
NI WAP-3701/3711 User’s Manual
To adjust the alignments of a pair of bridges’ directional antennas
Deploying the Access Point AP
Setting up Client Computers
Configuring IEEE 802.11g-related Settings
Checking if the TCP/IP-related Settings Work
Confirming the Settings of the AP and Client Computers
Configuring TCP/IP-related Settings
Checking if the IEEE 802.11g-related Settings Work
3. Type “ping defaultgateway”, where defaultgateway is the IP address of the default gateway of the wireless client computer, and then press Enter. If the gateway responds, go to the next step otherwise, see Appendix B, “TCP/IP Settings Problems,” to troubleshoot the problem
NI WAP-3701/3711 User’s Manual
Getting Started
‰ Configuring Advanced Settings
Web Console Configuration
‰ Configuring TCP/IP-related Settings
‰ Configuring IEEE 802.11g-related Settings
NI WAP-3701/3711 User’s Manual
Menu Structure
Web Console Configuration
Overview
Home and Refresh Buttons
Save, Save & Restart, and Cancel Buttons
Associated Wireless Clients
Viewing Status
Web Console Configuration
Current DHCP Mappings
System Log
Link Monitor AP Client mode only
NI WAP-3701/3711 User’s Manual
General Operations
Specifying the Operational Mode
Web Console Configuration
Web Console Configuration
Administrative Password
Managing the Firmware
Upgrading the Firmware by HTTP
NI WAP-3701/3711 User’s Manual
Backing up and Restoring Configuration Settings by HTTP
Upgrading Firmware by TFTP
Web Console Configuration
Web Console Configuration
NI WAP-3701/3711 User’s Manual
6. Choose TFTP as the Firmware management protocol
6. Choose TFTP as the Firmware management protocol
Backing up and Restoring Configuration Settings by TFTP
Web Console Configuration
NI WAP-3701/3711 User’s Manual
Web Console Configuration
Configuring TCP/IP-related Settings
Resetting the Configuration to Factory Defaults
Addressing
Web Console Configuration
DHCP Server AP/Bridge modes only
Basic
Static DHCP Mappings
Web Console Configuration
Configuring IEEE 802.11g-related Settings
Communication
Link Integrity
Web Console Configuration
Wireless Distribution System
Association Control
AP Load Balancing
3-14
Web Console Configuration
Sample wireless bridge network topology
NI WAP-3701/3711 User’s Manual
NI WAP-3701/3711 User’s Manual
Security
Web Console Configuration
Basic
NI WAP-3701/3711 User’s Manual
Web Console Configuration
Behavior of the “This AP Only” wireless client isolation option
When AP 1 and AP 2 are using the “This AP Only” option, wireless traffic between STA 1 and STA 2 is blocked by AP 1, whereas wireless traffic between STA 2 and STA 3 which are associated with different APs is still allowed. If the “All APs in This Subnet” option is used as shown in the above figure, AP 1 and AP 2 communicate with each other via an inter-AP protocol to share their STA association information to block wireless traffic among all the STAs
Shared Key , and Auto
Web Console Configuration
y Open System. No authentication, no data encryption
NI WAP-3701/3711 User’s Manual
2. Set the Access control type to inclusive
MAC-Address-Based Access Control
Web Console Configuration
2. Set the Access control type to exclusive
Sample MAC ACL file
IEEE 802.1X/RADIUS AP mode only
Web Console Configuration
NI WAP-3701/3711 User’s Manual
IEEE 802.1X and RADIUS
Web Console Configuration
Internet
NI WAP-3701/3711 User’s Manual
IP Protocol Filters
Configuring Advanced Settings
Packet Filters
Ethernet Type Filters
System Log
Management
TCP/UDP Port Filters
UPnP
3-23
SNMP
Web Console Configuration
NI WAP-3701/3711 User’s Manual
MAC-Address-Based Access Control
Default Settings
Setting Name
Default Value
Management
Default Settings
NI WAP-3701/3711 User’s Manual
LAN Interface
Wireless Settings Problems
Troubleshooting
NI WAP-3701/3711 User’s Manual
TCP/IP Settings Problems
Troubleshooting
Internet
NI WAP-3701/3711 User’s Manual
Unknown Problems
Troubleshooting
Wireless Router/AP Browser
Troubleshooting
NI WAP-3701/3711 User’s Manual
y The firmware of the AP may be stuck in an incorrect state
FCC Radiation Exposure Statement
Regulatory Statement
Federal Communication Commission Interference Statement
R&TTE Compliance Statement
EU Countries Intended for Use
Safety
NI WAP-3701/3711 User’s Manual
Regulatory Statement
Technical Support and Professional Services
National Instruments Corporate Headquarters
Service Information
NI AirWorks NI-WAP-3701/3711 User’s Manual
Worldwide Technical Support and Product Information
