Manuals / National Instruments / Computer Equipment / Network Router

National Instruments WAP-3701, WAP-3711 user manual Appendix C, Regulatory Statement, Appendix D

Models: WAP-3701 WAP-3711

1 47

Page 4

Appendix C	Regulatory Statement	C-1
Appendix D	Technical Support and Professional Services	D-1

Page 4

Image 4

National Instruments WAP-3701 Appendix C, Regulatory Statement, Appendix D, Technical Support and Professional Services

Contents

NI WAP-3701/3711 User’s Manual First Edition, SeptCopyright Notice TrademarksDisclaimer NI WAP-3701/3711 User’s ManualTable of Contents Technical Support and Professional Services Appendix CRegulatory Statement Appendix D‰ Overview ‰ Package Checklist ‰ Product Features Introduction‰ Product Specifications Package Checklist Product FeaturesProduct Specifications OverviewSoftware Features PowerNI WAP-3701/3711 User’s Manual IntroductionGetting Started ‰ First-Time Installation and Configuration‰ Deploying the Access Point AP ‰ Setting up Client Computers ‰ Confirming the Settings of the AP and Client ComputersFirst-Time Installation and Configuration Step 1 Select the Power SourceStep 3 Set up the computer’s IP address Step 4 Use the web-based manager to configure the NI WAP-3701/3711NI WAP-3701/3711 User’s Manual Getting Startedinstructions Step 5 Select the Operational Mode for NI WAP-3701/3711Step 6 Configure the NI WAP-3701/3711’s IEEE 802.11 settings Step 7 Review and Apply SettingsNI WAP-3701/3711 User’s Manual Getting StartedDeploying the Access Point AP Setting up Client ComputersConfiguring IEEE 802.11g-related Settings To adjust the alignments of a pair of bridges’ directional antennasConfirming the Settings of the AP and Client Computers Configuring TCP/IP-related SettingsChecking if the IEEE 802.11g-related Settings Work Checking if the TCP/IP-related Settings WorkNI WAP-3701/3711 User’s Manual 3. Type “ping defaultgateway”, where defaultgateway is the IP address of the default gateway of the wireless client computer, and then press Enter. If the gateway responds, go to the next step otherwise, see Appendix B, “TCP/IP Settings Problems,” to troubleshoot the problemGetting Started Web Console Configuration ‰ Configuring TCP/IP-related Settings‰ Configuring IEEE 802.11g-related Settings ‰ Configuring Advanced SettingsMenu Structure Web Console ConfigurationOverview NI WAP-3701/3711 User’s ManualSave, Save & Restart, and Cancel Buttons Associated Wireless ClientsViewing Status Home and Refresh ButtonsCurrent DHCP Mappings System LogLink Monitor AP Client mode only Web Console ConfigurationGeneral Operations Specifying the Operational ModeWeb Console Configuration NI WAP-3701/3711 User’s ManualAdministrative Password Managing the FirmwareUpgrading the Firmware by HTTP Web Console ConfigurationBacking up and Restoring Configuration Settings by HTTP Upgrading Firmware by TFTPWeb Console Configuration NI WAP-3701/3711 User’s ManualNI WAP-3701/3711 User’s Manual Web Console Configuration6. Choose TFTP as the Firmware management protocol Backing up and Restoring Configuration Settings by TFTP Web Console ConfigurationNI WAP-3701/3711 User’s Manual 6. Choose TFTP as the Firmware management protocolConfiguring TCP/IP-related Settings Resetting the Configuration to Factory DefaultsAddressing Web Console ConfigurationDHCP Server AP/Bridge modes only BasicStatic DHCP Mappings Web Console ConfigurationConfiguring IEEE 802.11g-related Settings CommunicationLink Integrity Web Console ConfigurationWireless Distribution System Association ControlAP Load Balancing Web Console ConfigurationWeb Console Configuration Sample wireless bridge network topologyNI WAP-3701/3711 User’s Manual 3-14Security Web Console ConfigurationBasic NI WAP-3701/3711 User’s ManualWeb Console Configuration Behavior of the “This AP Only” wireless client isolation optionWhen AP 1 and AP 2 are using the “This AP Only” option, wireless traffic between STA 1 and STA 2 is blocked by AP 1, whereas wireless traffic between STA 2 and STA 3 which are associated with different APs is still allowed. If the “All APs in This Subnet” option is used as shown in the above figure, AP 1 and AP 2 communicate with each other via an inter-AP protocol to share their STA association information to block wireless traffic among all the STAs NI WAP-3701/3711 User’s ManualWeb Console Configuration y Open System. No authentication, no data encryptionNI WAP-3701/3711 User’s Manual Shared Key , and AutoMAC-Address-Based Access Control Web Console Configuration2. Set the Access control type to exclusive 2. Set the Access control type to inclusiveIEEE 802.1X/RADIUS AP mode only Web Console ConfigurationNI WAP-3701/3711 User’s Manual Sample MAC ACL fileWeb Console Configuration InternetNI WAP-3701/3711 User’s Manual IEEE 802.1X and RADIUSConfiguring Advanced Settings Packet FiltersEthernet Type Filters IP Protocol FiltersManagement TCP/UDP Port FiltersUPnP System LogSNMP Web Console ConfigurationNI WAP-3701/3711 User’s Manual 3-23Default Settings Setting NameDefault Value MAC-Address-Based Access ControlDefault Settings NI WAP-3701/3711 User’s ManualLAN Interface ManagementTroubleshooting Wireless Settings ProblemsTCP/IP Settings Problems TroubleshootingInternet NI WAP-3701/3711 User’s ManualUnknown Problems TroubleshootingWireless Router/AP Browser NI WAP-3701/3711 User’s ManualNI WAP-3701/3711 User’s Manual Troubleshootingy The firmware of the AP may be stuck in an incorrect state Regulatory Statement Federal Communication Commission Interference StatementR&TTE Compliance Statement FCC Radiation Exposure StatementSafety NI WAP-3701/3711 User’s ManualRegulatory Statement EU Countries Intended for UseTechnical Support and Professional Services Service Information NI AirWorks NI-WAP-3701/3711 User’s ManualWorldwide Technical Support and Product Information National Instruments Corporate Headquarters