3. OPERATION
Connecting the Power Cable and Turn on the Projector
Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed.
1.Connect the supplied power cable to the projector.
|
|
| R |
|
|
|
|
|
| EW | OP |
|
|
D |
| SU |
|
| ||
SS | TA |
|
|
| ||
RA | EC | TS |
|
|
| |
| C | CA |
|
|
| |
|
| CP |
|
|
|
|
|
| TS |
| YB | D | |
|
| UJ |
| / | TS | |
|
| OT | DA |
| NO | |
|
| UA |
|
|
| |
EC |
|
|
|
|
|
|
RU |
|
|
|
|
|
|
OS |
|
|
|
|
|
|
LECNAC |
|
|
|
|
|
|
To turn off the projector:
First press the “off” button on the remote control (“ON/STAND BY” button on the projector cabinet) for a minimum of two seconds. The power indicator will glow orange. After the projector turns off, the cooling fans keep operating for one minute.
NOTE: Do not disconnect the power cable during this time. Then, unplug the power cable. The power indicator will go out.
Status of indicator light: turn on
|
|
|
|
| R |
|
|
|
|
|
|
|
|
|
| TC |
|
|
| E |
|
|
|
|
|
|
|
|
|
|
|
|
| T |
|
|
|
|
|
|
|
|
| |
|
|
|
| N |
|
|
|
|
|
|
|
|
| |
| EL |
|
|
| E |
|
|
|
|
|
|
|
|
|
| ES |
|
|
|
|
|
|
|
|
|
|
|
| |
UN |
|
|
|
|
|
|
|
|
|
|
|
| AU | DIO |
EM |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RG | B |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| S- | VID | EO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| VID | EO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| RO | L |
|
|
|
|
|
|
|
|
|
|
|
| NT |
|
|
|
|
|
| |
|
|
|
|
|
| CO |
|
|
|
|
|
|
| |
|
|
| RD |
| PC |
|
|
|
|
|
|
|
| |
|
| CA |
|
|
|
|
|
|
|
|
|
| ||
| C |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| US | B |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
AC | IN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
stand by
STATUS
POWER
steady orange light
ON/
STAND BY
flashing one minute
STATUS
POWER
steady light
STATUS
POWER
Plug the supplied power cable in the wall outlet. The projector will go into its standby mode and the power indicator will glow orange.
2.Turn on and off the Projector
OFF 
ON
Power ON button
VIDEO
RGB 1 | RGB 2 | PJ |
MENU |
| LASER |
Eco mode:
stand by
STATUS
POWER
steady orange light
flashing green light | steady green light |
ON/
STAND BY
flashing one minute | steady light |
STATUS | STATUS |
POWER | POWER |
| N |
|
|
|
E |
|
|
| |
M |
|
|
|
|
| SELECT | L | Indicator | |
|
| E | ||
|
| C | ||
|
| N |
| |
|
| C | A |
|
| ENTER |
|
| SOURCE |
|
|
|
| |
flashing green light
Status of indicator light: turn off
steady green light (Eco mode)
|
| AUTO |
| PC CARD |
|
|
| ACCESS | |
|
| ADJUST |
| STATUS |
|
|
|
| POWER |
|
| / | BY |
|
P |
| ON |
|
|
| STAND |
| ||
C | C |
| ||
| ON |
|
|
|
| T |
|
|
|
| ROL V |
|
|
|
| ID |
|
|
|
| E |
|
|
|
| O | Power ON/STAND BY button | ||
|
| S- |
|
|
|
| V |
|
|
|
| IDEO |
|
|
To turn on the projector:
Only after you press the “On” button on the remote control (“ON/ STAND BY” button on the projector cabinet) will the power indicator turn to green and the projector become ready to use.
ON
STATUS
POWER
steady green light
ON/
STAND BY
cooling down
STATUS
POWER
Press a minimum of two seconds.
stand by
STATUS
POWER
NOTE: To turn the projector on by plugging in the power cable, use the menu and enable the “Auto Start” feature. (See page
NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.
change to flashing | steady orange light |
green light |
|
E – 24
