NEC NC2500S 1-3-2.Rear of the projector

1. What’s in the Box? and the Names of the Projector Parts

1-3-2. Rear of the projector

1

5

2

4

3

1. Air inlet

Air is taken in here to provide cooling of the projector. Do not cover the air inlet.

2. Level adjusters (in four positions on bottom)

In the ordinary installation, you can adjust the projector inclination at 4 positions.

3. Tilt feet (in two positions on bottom)

These adjust the tilting angle of the projector. Please contact your dealer/distributor to setup and adjust this projector.

4. Lamp door

This opens to allow the lamp to be replaced. Please contact your dealer/distributor to install and to replace the lamp bulb and lamp house.

5. Rear status indicator

These indicate the status of the projector. When the projector is operating normally, these light/blink in green or orange. When an error occurs, they light/blink in red. When an error occurs, check the contents of the display on the LCD screen. (See page 39)

NOTE • Do not cover the air inlet and outlet during operation. Inadequate air intake may lead to a rise in inside temperature, thus causing a free or serious projector failure.

Caution:

Only service personnel should open the lamp door.

7

Contents

DLP Cinema® Projector User’s Manual Important Information Important Information Page Page Page Page Page Table of Contents Table of Contents 1.What’s in the Box? and the Names of the Projector Parts 2.Installation and Connection 3.Projection of Images (Basic Operation) What’s in the Box? and the Names of the Projector Parts 1-1.Features 1.What’s in the Box? and the Names of the Projector Parts 1-2.What’s in the Box Page 1-3.Names of the Projector Parts 1-3-1.Front of the projector 1-3-2.Rear of the projector 1-3-3.Lamp power supply unit (LPSU) 1-3-4.Connection terminals 1-3-5.Control panel Page 1-4.Names on the Remote Control Page Page Installation and Connection 2-1.Steps for setting up and connecting 2-2.Connecting the image input terminals 2-3.Connecting the various control terminal Projection of Images (Basic Operation) 3-1.Steps of projecting images 3-2.Turning your projector on Page 3-3.Selecting the title of input signal 3-4.Adjusting the position and the size of projected screen 3-4-1.Displaying the test pattern 3-4-2.Adjusting the position of the projected screen (Lens shift) 3-4-3.Fine adjustment of the size of the projected screen (Zoom) 3-4-4.Focusing the projected screen (Focus) 3-4-5.Adjusting the brightness of the projected screen (Lamp output) 3-5.Turning your projector off Using Menus 4-1.Basic operation with adjustment menus 4-1-1.Screen display 4-1-2.Operating menus 3Press the [MENU CTL] DOWN button 4Press the [MENU CTL] LEFT/RIGHT button to select the submenu “Version.” 5Press the [MENU CTL] DOWN button 6Press the [MENU CTL] DOWN button 7Press the [MENU CTL] LEFT/RIGHT button to select the submenu “Data.” 4-1-3.How to enter alphanumeric characters 4-2.Table of adjustment menus 4-3.Title Select 4-3-1.Title select (Title Memory) 4-3-2.Test Pattern 4-4.Configuration 4-4-1.Lamp Setup 4-5.Title Setup 4-6.Information 4-6-1.Lamp 4-6-2.Macro Key 4-6-3.Usage 4-6-4.Error Code 4-6-5.Version 4-6-6.IP Address 4-6-7.MMS Status Maintenance of Your Projector 5-1.Cleaning the Cabinet 5-2.Cleaning the Lens Appendix 6-1.Troubleshooting 6-1-1.Problems and where to check 6-2.Indicator display list 6-2-1.POWER indicator 6-2-2.STATUS indicator 6-2-3.MMS STATUS indicator 6-2-4.Rear STATUS indicator 6-3.Error code list Page 6-4.Operation using an HTTP browser 6-4-1.Overview 6-4-2.Preparation before use 6-4-3.Handling of the address for operation via a browser 6-4-4.Structure of the HTTP server 6-5.Outline Drawing 6-5-1.Projector head outline drawing 6-5-2.Lamp power supply unit outline drawing 6-6.Specifications Caracteristiques techniques Technische Daten 6-7.Pin Assignment and Functions of Terminal 6-7-1.PC CONTROL connector (D-Sub9 pin) 6-7-2.Remote control input connector (REMOTE IN) (Stereo mini) 6-7-3.LAN port (LAN-A, LAN-B) (RJ-45) 6-7-4.External control connector (GP I/O) (D-Sub37 pin) Page 6-7-5. SDI-A, SDI-B (HD-SDIinput connector) (BNC) 6-7-6. DVI-A, DVI-B(DVI digital Input connector) (DVI-D24 pin) 6-8.Related products list Page 7N8P6673