Creating a video wall, Cable Management | NEC PX-50XM5G, PX-61XM4G

Creating a video wall

With built-in matrix display capability, you can create a (2×2, 3×3, 4×4, 5×5) video wall.

• Connect signal cables and remote cables as shown below.

Video signal

	IN	RCA phono plug
VIDEO Signal	IN
VIDEO Signal
Remote	IN
control

				RGB/DVD/HD signal
					BNC connector
(	VIDEO	BNC connector	OUT
VIDEO1 I N / OUT)			OUT
VIDEO1 I N / OUT)			VIDEO Signal	RGB signal/	IN
VIDEO 3	VIDEO 2		VIDEO Signal		IN

				DVD/HD signal
				DVD/HD signal

(		AUDIO1 R
MONO
)	L
		Y
		DVD1

I N		control
OUT REMOTE	OUT	control
		Remote

Remote IN control

Cr/Pr	R/
G/ Y		RGB2
Cb/Pb	B/	/ DVD2
HD		/ HD2
VD
( IN / OUT		RGB 1
)
I N
REMOTE
OUT

OUT

OUT

RGB signal/ DVD/HD signal

Remote control

Note:

1.The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT.

When LOOP OUT is ON, do not connect an OUTPUT signal from another unit as it may damage the other unit due to an extraordinary load.

2.LOOP OUT can not be turned ON while signals are input to the RGB1 terminal.

3.LOOP OUT can be turned ON while signals are input to the RGB1 terminal if the POWER is switched ON.

Information

•To loop signals out to another plasma display, set the LOOP OUT to ON.

•To create a video wall, set the VIDEO WALL menu items properly.

•To connect monitors, please use a 1~2m (3.3~6.6 feet) BNC cable (any commercially available cable).

•If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.

•Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024×768, 60Hz signal.

•A distribution amplifier is particularly recommended when creating a 3×3 (or greater) video wall.

•When looping from plasma to plasma, a 1~2m (3.3~6.6 feet) 15 pin male D-Sub - 5BNC conversion cable is required.

Cable Management

Using the cable clamps provided with the plasma display; Bundle the signal and audio cables at the back of the unit to connect to the display.

42 inch

50/61 inch

Back of the unit

Back of the unit

mounting holes

mounting holes

To attach	To detach
1.	2.
	clamp
	cables
mounting hole

Downloaded From TV-Manual.com Manuals

En-6

Image 7

NEC PX-50XM5G, PX-61XM4G, PX-42XM4G user manual Creating a video wall, Cable Management, RGB/DVD/HD signal

Contents

PlasmaSync Plasma Monitor User’s Manual Important Information Precautions Disposing of your used product Contents Ventilation Requirements for enclosure mounting Installation Creating a video wall RGB/DVD/HD signalCable Management Handling the remote control Using the remote controlBattery Installation and Replacement Using the wired remote control mode Front View Turns the monitor’s power on and offReceives the signals from the remote control Part Names and Function Rear View/ Terminal Board Connection Example Connecting a TV tunerInch Cb/Pb 51/61 inch Remote Control Basic Operations Wide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF Supported resolution Split Screen Operations Operations in the Side-by-side modeShowing a couple of pictures on the screen at the same time Zooming in on a specific input Operations in the Picture-in-picture modeSelecting the input signals to be displayed Adjusting the OSM controls Menu Operations Advanced menu modeActual screen may be different from the ones in this manual Menu Tree Reset Video Wall Restoring the factory default settings Reducing noise in the picture Picture Settings MenuAdjusting the picture Setting the color temperature Changing the Gamma Curve Adjusting the color to the desired levelMaking the Low Tone adjustments Adjusting the colors Adjusting the Position, Size, Fine Picture, Picture Adj Audio Settings MenuImage Adjust Settings Menu Setting the allocation of the audio connectors Setting the RGB1 connector Option1 Settings MenuSetting the on-screen menu Setting the BNC input connector type Setting the Input Skip Setting high definition images to the suitable screen sizeResetting to the default values Setting the picture to suit the movie Option2 Settings MenuSetting the power management for computer images POWER/STANDBY indicator Setting the time Orbiter settingsInverse Settings Orbiter Function settings Gray Level settings Setting the gray level for the sides of the screenSetting the screen size for S1/S2 video input Soft Focus settings Using the timer Option3 Settings MenuSetting the picture size for RGB input signals Setting the signal and black level for DVI signal Special characters in the Program Timer screen Program Timer settingsTo reset the program To reset the data Remote ID setting Setting the power on modeEnabling/disabling remote control wireless transmission Loop Out setting Video Wall setting ID number setting On Delay settings DISP. Mode settingsAuto ID settings Image Adjust settings PLE Link PLE Link settingsRepeat Timer settings Repeat Timer Displaying the entire image during Digital Zoom operations Option4 Settings MenuDisplaying still images in the sub screen Displaying the information as a text Switching the input source quickly Source Information Menu Advanced OSM Settings MenuLanguage Settings Menu Color System Settings Menu Pin Assignments External Control Symptom Checks Remedy Troubleshooting Supported resolution 42XM4 Table of Signals SupportedComputer input signals supported by this system Full CVT standard compliant True Full DVI Supported resolution 50XM5/61XM4 True Full 42XM4 Specifications 50XM5 61XM4