Manuals / Brands / Computer Equipment / Computer Monitor / NEC / Computer Equipment / Computer Monitor

NEC XV29 Plus e. SCAN, b. WIDTH, c. HEIGHT, g. BRIGHT, d. SIDE PIN, h. CONTRAST, f. NORMAL (raster), a. POSITION/CONTROL, Direct Control Screen

1 33

Download 33 pages, 465.59 Kb

Direct Control Screen

You can adjust the raster, visual and sound using the direct key on the remote control.

To switch to another control screen, press any one of the other keys.*To end the OSM display, press EXIT.*If no key operation is made within 3 seconds, the OSM display will disappear.a. POSITION/CONTROL

Press © to move the image right. Press ß to move the image left.

Press ▲ to move the image up. Press ▼ to move the image down.

b. WIDTH

Press to adjust the horizontal size of the image.

f. NORMAL (raster)

Press to reset all the stored adjustment raster data and recall the factory preset data. When a specific control is selected, this key resets the selected raster adjustments.

23

c. HEIGHT

Press to adjust the vertical size of the image.

d. SIDE PIN

Press to adjust the curvature of the edges of the left and right side of the display image either inward or outward. The image should be adjusted to attain a straight line on the left and right sides.

e. SCAN

Press to select the scan mode: over scan and under scan.

g. BRIGHT

Press to adjust the brightness of video display.

h. CONTRAST

Press to adjust the contrast of video display.

24

Contents

MultiSync©XV29Plus MultiSync© XV29 Plus CAUTION DOC compliance Notice ATTENTION DOC avis de conformation NEC Multimedia Monitor Products HOW LONG IS THE WARRANTY WHO IS PROTECTED This warranty may be enforced only by the first purchaser WHAT IS COVERED AND WHAT IS NOT COVERED 1. Introduction 2. Part Names and Functions 3. Installation 4. Operation 7. Timing Charts Introduction to the MultiSync XV29 Plus Monitor The features you’ll enjoy include: Contents of the Package Part Names and Functions 12 AC Input 13 VIDEO 14 RGB AUDIO 15 MONITOR OUT (R/L) 16 DIP SWITCH Remote Control Unit 1 POWER ON/OFF 2 DEGAUSS 3 Input Select OSM Control Raster Control 7 WIDTH (+ / –) Adjusts the horizontal size of the image 8 HEIGHT (+ / –) Adjusts the vertical size of the image Battery Installation and Replacement Remote Control Cautions Operating Range Functions of DIP SW The drawing below shows the original factory settings of DIP Switch Functions and Settings of DIP SW Set all the pin except No. 2 to the OFF/OPEN position during normal operation The pins nos 5 and 6 are not used Installation Connecting Your PC or Macintosh Computer 1.Turn off the power to your monitor and computer 4.Turn on the monitor and the computer Connecting Your VCR or Laser Disc Player 1.Turn off the power to your monitor and VCR or laser disc player D-Sub15 Pin RGB Signal Composition Pin Assignments and Signal Levels for 15 pin RGB D-SUB15pin RGB Input Connector Pin No Signal to be connected (D-SUB15 pin) Operation Direct Control Screen To switch to another control screen, press any one of the other keys *To end the OSM display, press EXIT *If no key operation is made within 3 seconds, the OSM display will disappear a. POSITION/CONTROL i. NORMAL( visual) j. MUTE k. VOLUME Accessing OSM OSM Menus H-position/H-width/Pin-cushionControls Group H-POSITION :Pressing + or - moves the image horizontally right or left H-WIDTH PIN-CUSHION PIN-BALANCE RGB Controls Group The RGB Controls allow you to adjust the white balance for RGB input B-GAIN R, G B-BIAS Volume Control The Volume control allows you to adjust the volume VOLUME : Pressing + or - increases or decreases the volume NOTE: When you mutes the sound, the MUTE display appears All Visual Settings OSM System Control Menu POSITION CONTROL + POSITION CONTROL EXIT POWER ON MODE OSM ON/OFF Troubleshooting Specifications Page Dimensions Timing Charts Separate Sync Composite Sync Composite Sync. & Video (Sync. on Green) VGA Compatible XGA-2Compatible Mac U, Quadra or LC Compatible Resolution Vertical Frequency (O) Vertical Period (P) Vertical Pulse Width (Q) Vertical Back Porch (R) Vertical Active Area Signal Identification for Raster Preset Eligibility/Return for Exchange Procedure