NETGEAR WG602v3 WG602v3 Wireless Access Point Rear Panel

Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3

2-6 Introduction

202-10060-02, February 2005

WG602v3 Wireless Access Point Rear Panel

Figure 2-2: WG602v3 rear panel

Power Socket

This socket connects to the WG602v3 power adapter.

Reset and Restore to Factory Defaults Button

The reset and restore to defaults button located between the Ethernet RJ-45 connector and the

power socket resets the WG602v3 when pushed once or restores to the factory default settings

when pushed and held for 10 seconds.

RJ-45 Ethernet Port

Use the WG602v3 Ethernet RJ-45 port to connect to an Ethernet LAN through a device such as

a hub, switch, or router.

Detachable Antenna

The WG602v3 provides a detachable antenna. Be sure the antenna is securely fastened.

Wireless Wireless LAN Link Activity Indicator

Off

Green On Indicates no wireless link detected.

Wireless link enabled, no activity.

Green Blink Wireless link activity.

LED DESCRIPTION

Power

Socket

RJ-45Ethernet

Port

Reset& Restore

Button

Detachable

Antenna

Contents

Main NETGEAR, INC. Technical Support Please register to obtain technical support Trademarks Statement of Conditions 202-10060-02, February 2005 Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice NETGEAR NETGEAR WG602v3 54 Mbps Wireless 202-10060-02, February 2005 Canadian Department of Communications Compliance Statement Product and Publication Details Contents Page Page Page Chapter 1 About This Manual Audience, Scope, Conventions, and Formats How to Use This Manual How to Print this Manual Page Chapter 2 Introduction About the NETGEAR WG602v3 54 Mbps Wireless Access Point Support for Standards Key Features 802.11g Standards-based Wireless Networking Autosensing Ethernet Connections with Auto Uplink Wireless Multimedia (WMM) Support Compatible and Related NETGEAR Products System Requirements Whats In the Box? Hardware Description WG602v3 Wireless Access Point Front Panel WG602v3 Wireless Access Point Rear Panel Chapter 3 Basic Installation and Configuration Observing Placement and Range Guidelines Default Factory Settings Understanding WG602v3 Wireless Security Options Wireless Data Security Options Range: Up to 300 Foot Radius Installing the NETGEAR WG602v3 54 Mbps Wireless Access Point A 1S 2C 3D 4V Two Ways to Log In to the WG602v3 How to Log in Using the Default IP Address of the WG602v3 Page How to Log In to the WG602v3 Using Its Default NetBIOS Name Using the Basic IP Settings Options Understanding the Basic Wireless Settings Page Understanding Wireless Security Options Page Information to Gather Before Changing Basic Wireless Settings How to Configure WEP Wireless Security How to Configure WPA-PSK Wireless Security How to Configure WPA2-PSK Wireless Security How to Configure WPA-PSK/WPA2-PSK Wireless Security How to Restrict Wireless Access by MAC Address Page Page Page Reference Manual for the NETGEAR 54 Mbps Wireless Access Point WG602v3 4-2 Management 202-10060-02, February 2005 This screen shows the following parameters: Table 4-1. General Information Fields Viewing a List of Attached Devices Upgrading the Wireless Access Point Software Page Rebooting and Resetting Factory Default Options Restoring the WG602v3 to the Factory Default Settings Using the Reset Button to Reboot or Restore Factory Defaults Changing the Administrator Password Chapter 5 Advanced Configuration Understanding Advanced Wireless Settings Configuring Wireless Distribution System Links How to Configure Wireless Bridge Links Page How to Configure a WG602v3 as a Point-to-Point Bridge How to Configure Wireless Multi-Point Bridging How to Configure Wireless Repeating Page Page Chapter 6 Troubleshooting Troubleshooting No lights are lit on the access point. I cannot configure the wireless access point from a browser. I cannot access the Internet or the LAN with a wireless capable computer. When I enter a URL or IP address I get a timeout error. Using the Reset Button to Restore Factory Default Settings Page Appendix A Specifications This appendix provides the NETGEAR WG602v3 54 Mbps Wireless Access Point technical specifications. Specifications for the WG602v3 Page Appendix B Wireless Networking Basics Wireless Networking Overview Infrastructure Mode Ad Hoc Mode (Peer-to-Peer Workgroup) Network Name: Extended Service Set Identification (ESSID) Authentication and WEP Data Encryption 802.11 Authentication Open System Authentication Shared Key Authentication 802.11Authentication Open System Steps Overview of WEP Parameters 802.11Authentication Shared Key Steps Key Size WEP Configuration Options Wireless Channels WPA and WPA2 Wireless Security How Does WPA Compare to WEP? How Does WPA Compare to WPA2 (IEEE 802.11i)? What are the Key Features of WPA and WPA2 Security? Page Wired Network with Optional 802.1x Port Based Network Access Control Wireless LAN Page Page Page Is WPA/WPA2 Perfect? Product Support for WPA/WPA2 Page Page Appendix C Network, Routing, Firewall, and Cabling Basics Basic Router Concepts What is a Router? IP Addresses and the Internet Page Netmask Subnet Addressing Page Page Private IP Addresses Single IP Address Operation Using NAT IP Configuration by DHCP Domain Name Server Routing Protocols Internet Security and Firewalls What is a Firewall? Stateful Packet Inspection Denial of Service Attack Ethernet Cabling Category 5 Cable Quality Inside Twisted Pair Cables Uplink Switches, Crossover Cables, and MDI/MDIX Switching Page Page Appendix D Preparing Your PCs for Network Access Preparing Your Computers for TCP/IP Networking Configuring Windows 98 and Me for TCP/IP Networking Installing or Verifying Windows Networking Components Enabling DHCP to Automatically Configure TCP/IP Settings DHCP Configuration of TCP/IP in Windows 98 and Me Selecting the Windows Internet Access Method Verifying TCP/IP Properties for Windows 98 or Me Configuring Windows 2000 or XP for TCP/IP Networking Installing or Verifying Windows Networking Components DHCP Configuration of TCP/IP in Windows XP Page DHCP Configuration of TCP/IP in Windows 2000 Page Verifying TCP/IP Properties for Windows XP or 2000 Page Glossary Use the list below to find definitions for technical terms used in this manual.