Explicit reference is made to the risks of using highly flammable, combustible, toxic,
Initial operation
Delivery, instruction on safety procedures, handling and maintenance and initial operation are generally carried out by our authorized specialist.
If this is not the case, the operator is responsible for instructing machine users.
Commissioning/operation
Please remember that the voltage in the building being cleaned must concur with that given on the machineʼs type plate.
Assembly instructions
The motor head and bar are supplied separately packed. First release the hexagon socket srews in the shaft
adjustment unit (17).
Then feed the bar (7) gently as far as it will go into the shaft adjustment unit (17).
Align the handle bar (1) parallel with the wheels (9), so that the open side of the housing of the top shaft element (3) is facing to the rear.
Then tighten the hexagon socket screws again.
Wind the electric cable (18) around the handle bar (a) and cable hook (8).
Preparations for use
Grasp the handle bar (1) with both hands and tip the machine until it is resting on both wheels (A).
Then wheel the machine to its place of work and plug the electric cable into the power supply.
Lay the accessories (11), i.e. brush or drive plate with pad, on the floor.
Now tip the machine back onto the wheels and push it over the brush (or drive plate) until the drive star and brush flange are vertically aligned. Lower the machine onto the brush (B).
Then squeeze the shaft adjustment lever (5) and lower the bar (7) into its working position. Both arms should be extended loosely downwards (C).
Align the machine horizontally above the working element (brush or drive plate), press the switch lock
(4) and press the brush motor switch (2) briefly. The accessory automatically engages.
Machine use
Press the brush motor swith (2) (to the right or left). The motor starts.
If you raise the bar (7) slightly, the machine moves to the right (D).
If you lower the bar, the machine moves to the left (D). If you keep the bar in its central position, the machine
works on the spot.
After use
Squeeze the shaft adjustment handle (5) and shift the bar (7) into its vertical position.
Then tip the machine onto its wheels (9) and press the brush motor switch (2) briefly. The accessory (11) disengages.
Remove the plug from the power socket and wind the electric cable (18) around the handle bar (1) and cable hook (8).
Thorough cleaning the easy way
For thorough cleaning, the
Liquid tank (13)
Scrubbing brsuh (11) or drive plate with black pad (19). Fasten the tank to the mounting (14).
Slide the outlet hose (12) onto the water connector (16). Fill the tank (13). Then fit the brush or drive plate with
pad.
Control the flow of liquid with the tank lever (15) by pulling the lever (15) upwards.
Vacuum the dirty wash solution a section at a time with a water extractor.
Shampooing thoroughly and efficiently
For shampooing, the machine is equipped with the following accessories:
- Liquid tank; 0.3 Perlon shampooing brush or Sapur pad for textile floorcoverings.
The working procedure is in principle the same as for thorough cleaning.
Start the machine with the shampooing brush dry. Meter a small amount of liquid until the bristles are
saturated with foam.
Run the machine with the rotating brush from right to left or viceversa. Immediately after this, run the machine in the same way in the reverse direction, but with an overlap of about a quarter of the strip already treated (E.)
Only then run the machine in a spiral pattern over the shampooed strips. In doing so, work both strips at the same time (F.)
During shampooing it is highly advisable to immediately remove the
Assembly instructions for Spraymaster
Fit the holder for the spray can to the bar (7) with the holder pointing upwards and, when viewed from the operating side, to the left (G).
Hook the spray canʼs tongue onto the holder, pivoting the holder back until the ball catch engages.
Then slide the spring clip over the shaft adjustment unit
(7).
Attach the box on the right or left as desired (H).
Point the
8