Routine cleaning

 

 

 

Servicing instructions

 

 

For routine cleaning, your machine is equipped with the

the following instructions must always be

observed

 

 

 

 

following accessories:

 

 

 

When cleaning and servicing the machine, replacing

 

- Spraymaster, drive plate for pads, yellow-and-

 

brown or green pad for Low-Speed or Spraymaster,

parts or when changing over to a different function,

 

drive plate for pads, red pad for High Speed

 

switch off the drive and remove the plug.

Fill the spray can with the desired product.

 

The power supply lead must not be damaged by driving

Fit the drive plate with the desired pad.

 

over it, crushing, tugging etc.

 

 

Start the machine.

 

 

 

Check the power supply lead regularly for signs of

When you pull the Spraymaster lever a few times the

damage.

 

 

 

 

 

cleaning agent is sprayed onto the floor. Now start

The machine must not be used if the power supply lead

 

cleaning immediately until a shine is produced.

is not in perfect condition.

 

 

We advise cleaning the surface in relatively small areas

When using or replacing the power supply or

 

at a time. The machine is ideal for cleaning with

equipment supply leads, use only those specified by

 

polymer dispersions. The coatingʼs resistance to

the manufacturer.

 

 

 

 

foot traffic and general wear and tear is preserved.

When replacing the plug-and-socket connectors of

 

Streaks and marks are easier to remove.

 

power supply or equipment supply leads, splash

 

 

 

 

 

protection and mechanical strength must be

Polishing

 

 

 

assured.

 

 

 

 

 

 

 

When transporting the machine in lifts, put the shaft/

 

 

 

 

 

bar in a vertical position so that it cannot catch on

For polishing, equip your machine with the following

the lift walls.

 

 

 

accessories:

 

 

 

The shaft/bar is automatically secured against recoil by

 

- Drive plate for pads, white pad.

 

 

the patented shaft/bar adjustment unit.

Fit the drive plate with the pad.

 

 

Only the spray and cleaning agents suitable for the

Then start the machine.

 

 

 

machineʼs purpose may be used.

 

 

 

 

 

Never use highly flammable, combustible, toxic, health-

Service

 

 

 

hazardous, corrosive or irritant substances.

 

 

 

 

 

Repairs, including the fitting of spray agent lines

For repairs, please contact your specialist wholesaler or

and hoses, may only be carried out by approved

 

one of the service shops.

 

 

customer service shops or by specialists in this

You will be expertly and quickly served.

 

field who are familiar with all the relevant safety

Warning! This machine is only intended for use on

regulations.

 

 

 

Storage

 

 

 

 

 

level surfaces with a maximum gradient of up to 2 %.

 

 

 

 

Warning! This machine is not approved for use on

When the machine is not being used, store it in a dry

 

public paths and roads.

 

 

 

 

 

 

 

 

place and in normal room conditions (not below under

 

 

 

 

 

0°C).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Technical specifications

 

 

 

 

 

 

 

 

 

 

SD 43-165

SD 43-400

SDM 43-180

SDM 43-450

SDM 43-DUO

SDM 43-900/1500

SDM 53-1500

 

 

A.C. motor

230/50

230/50

230/50

230/50

230/50

230/50

230/50

 

 

Rated power

1000

1100

1200

1500

1200-1500

1800

1800

 

 

 

5,6

5,7

5,2

6,5

5,2/8,1

7,2

7,2

 

 

Brush (rpm)

165

400

180

450

190/380

900/1500

1500

 

 

Brush (mm)

430

430

430

430

430

430

530

 

 

Working height (mm)

250

250

330

330

330

130/320

130/320

 

 

Working weight (kg)

30

31

36

40

40

44

46

 

 

Protection class

I/IPx4

I/IPx0

I/IPx4

I/IPx0

I/IPx4

I/IPx0

I/IPx0

 

 

Belt-driven

X

X

X

X

X

X

X

 

 

Handle vibration level m/s2

1,05

1,05

1,05

1,05

1,05

1,05

1,05

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9