Manuals / Nilfisk-ALTO / Household Appliance / Vacuum Cleaner

Nilfisk-ALTO 46/53 C1700, FILTER SHAKER SWITCH See Figure, MillipaK SEM CONTROLLER See Figure

Models: 46/53

1 49

Download 49 pages 30.77 Kb

Page 17

C1700

OPERATION OF CONTROLS AND GAUGES

FILTER

SHAKER

SWITCH

C1640-2batt FIGURE 6

CONTROLLER

PUMP MOTOR

PUMP

FIGURE 7

HOPPER
SAFETY ARM
	TO
	ENGAGE
C1700
C1700	FIGURE 8

FILTER SHAKER SWITCH (See Figure 6)

The filter shaker switch is located on the instrument panel below the ignition switch. This is a momentary switch that will activate the filter shaker motors for 20 to 30 seconds to clear the dust control filter. The Impeller fan will stop when the filter shaker has been activated. The filter shaker will only operate with the hopper in the “DOWN” position.

Use the filter shaker to clear the filter when the dust control light comes on (warning bank) and just before dumping the hopper.

MillipaK SEM CONTROLLER (See Figure 7)

The controller is located in the seat compartment and includes a number of features designed to help the user track down operational faults, wiring faults or internal controller faults, including a flashing indicator light.

The Flash Codes are:

ON	No fault, normal condition
OFF	Internal controller fault
1 flash	Program Error
2 flashes	High Pedal Disable
3 flashes	MOSFET Short Circuit
4 flashes	Contactor fault or Motor Open Circuit
5 flashes	Not used
6 flashes	Accelerator wire off fault
7 flashes	Low or High battery voltage
8 flashes	Over temperature or timed cutback

HYDRAULIC PUMP (See Figure 7)

The pump is located in the seat compartment and is powered by a 45 amp circuit breaker (on the power panel) and a contact linked with the key switch. It functions at 1450 PSI and features 100 bar relief.

HOPPER SAFETY LOCK ARM (See Figure 8)

The hopper safety arm is located near the right front wheel well. The safety arm will prevent the hopper from dropping unexpectedly during service/maintenance.

TO ENGAGE THE SAFETY ARM:

1.Empty hopper

2.Set the parking brake.

3.Raise the hopper.

4.Lift safety arm to engage the slot on the hopper frame.

5.When work has been completed, return the safey arm to the stowed position.

WARNING

When the hopper is raised the safety arm must be engaged

before ANY work is done under the hopper.

American-Lincoln	1-17
ATS 46/53 Battery

Image 17

Nilfisk-ALTO 46/53 C1700, FILTER SHAKER SWITCH See Figure, MillipaK SEM CONTROLLER See Figure, HYDRAULIC PUMP See Figure

Contents

PARTS LIST ATS 46/53 BATTERYAmerican-Lincoln Technology OPERATOR’SAmerican-Lincoln TABLE OF CONTENTSATS 46-53Battery SERVICE CHART ATS 46/53 BatterySERVICE PRECAUTIONS SERVICE INSTRUCTIONSCHAPTER 3 OPTIONS DIMENSIONS CLEANING PATHWEIGHT TRAVEL SPEEDSQUEEGEE WARRANTYTANKS HOPPERATS 46/53 Battery MACHINE DIMENSIONSAmerican-Lincoln 65.41 cmSTANDARD HARDWARE & TORQUE VALUES The torque tolerance is ± on torque valuesHYDRAULIC TORQUE REQUIREMENTS Fraction DECIMAL-METRICCONVERSION TABLEDecimal MillimeterPREPARING THE MACHINE FOR OPERATION MACHINE PREPARATIONREAD THE INSTRUCTION BOOK SAFETY INSTRUCTIONSDANGER 1-13 ATS 46/53 BatteryAmerican-Lincoln American-Lincoln ATS 46-53Battery1-14 HORN BUTTON See Figure LIGHT SWITCH See FigureOPERATION OF CONTROLS AND GAUGES METER HOURCONDITION KEY SWITCH See FigureHOPPER SAFETY LOCK ARM See Figure FILTER SHAKER SWITCH See FigureTO ENGAGE THE SAFETY ARM C1700MAIN BROOM ADJUSTMENT See Figure SIDE BROOM ADJUSTMENT See figureSIDE BROOM LEVER MAINSWITCH SCRUB DECK SWITCHDUST CONTROL SWITCH See Figure SCRUB DECK SWITCH See FigureNON-RECYCLINGOR STANDARD SCRUBBING SYSTEM SOLUTION CONTROL See FigureRECYCLING OR ESP & AUTOFIL SYSTEM TO DISCONNECT WATER HOSEOPERATION OF CONTROLS AND GAUGES FOOT PEDAL PARKINGBRAKE FOOT PEDAL ACCELERATORHOPPER DUMP DOOR LEVER - See Figure HOPPER LIFT LEVER - See FigureSWITCH TURN SIGNALSWITCH TURN SIGNAL - 4-WayOption See FigureC1718 C1719FILTER PANEL LATCH See Figure FRONT COVER LATCH See FigureMAIN BROOM COMPARTMENT DOORS See Figure HYDRAULIC RESERVOIR LEVEL SIGHT GAUGEMAIN BROOM COMPARTMENTHOPPER FILTER COVER See Figure HOPPER DOOR LEVER See FigureHOPPER LIFT LEVER See Figure SOLUTION LEVEL WARNING LIGHT THE ESP RECYCLING SYSTEM ON/OFF SWITCHTHE ESP RECYCLING CONTROL PANEL See Figure DETERGENT LOW WARNING LIGHTDETERGENT TANK SOLUTION TANK SOLUTION TANKRECOVERY RECOVERYORIFICE STARTING BATTERY MACHINES PRE-STARTCHECKLISTSWEEPING AND DUST CONTROL SYSTEMS-HOWTHEY WORK DUST CONTROLBATTERY CHARGING INSTRUCTIONS POST-OPERATIONCHECKLISTSTORAGE FOR BATTERY-POWEREDMACHINES EMPTYING THE DEBRIS HOPPERMAIN AISLE HELPFUL HINTS FOR CLEANING OPERATION50 HOUR WEEKLY MAINTENANCE CHECKLIST SERVICE CHART100 HOUR MAINTENANCE CHECKLIST 250 HOUR MAINTENANCE CHECKLISTPage SERVICE PRECAUTIONS SERVICE PRECAUTIONSADJUSTING THE MAIN BROOM HEIGHT SWEEPING SYSTEM SERVICE MAIN BROOMMAIN BROOM LEVEL ADJUSTMENT CHECKING THE MAIN BROOM SWEEP PATTERNADJUSTING THE SIDE BROOM HEIGHT SIDE BROOM SERVICESIDE BROOM SERVICE SIDE BROOMCLEANING THE HOPPER HOPPER SERVICECLEANING THE DUST CONTROL FILTER HOPPERDUST FLAPS REPLACING THE DUST CONTROL FILTERADJUSTING THE BRAKE PEDAL BRAKE SERVICEADJUSTING THE BRAKES BRAKESCLEANING THE HYDRAULIC SYSTEM GENERAL MACHINE MAINTENANCEFILL HYDRAULIC RESERVOIR FILLING THE HYDRAULIC RESERVOIRRECOVERY HIGH WARNING LIGHT SOLUTION LOW WARNING LIGHTSOLUTION CONTROL Non-Recyclingor Standard SOLUTION CONTROL Recycling or ESP SystemADJUSTING CASTERS To service the bladesRECYCLING PUMP ESP SYSTEM RECYCLING PUMP STORAGEBATTERY ABBREVIATIONS - SETSCREWS PARTS LIST LEGENDABBREVIATIONS - SCREWS PROBABLE CAUSE PROBLEMREMEDY GENERAL TROUBLESHOOTINGPROBABLE CAUSE PROBLEMREMEDY 1. Worn scrubbing brushesORDERING PARTS