Manuals / Nilfisk-ALTO / Household Appliance / Vacuum Cleaner

Nilfisk-ALTO 46/53 manual Side Broom Lever, Main, SIDE BROOM LEVER See Figure

Models: 46/53

1 49

Download 49 pages 30.77 Kb

Page 18

SIDE

OPERATION OF CONTROLS AND GAUGES

SIDE

BROOM

LEVER

SIDE BROOM ADJUSTMENT

SIDE BROOM LEVER (See Figure 9)

The Side Broom Lever is located to the right of the instru- ment console. The handle pulled back and turned to the left, will raise the side broom and lock it into position.

To raise the side broom pull the lever back into the “UP” position.

To lower the side broom, move the lever out of the “UP” position and move it forward to the “DOWN” position.

NOTE

IF THE MAIN BROOM IS ENGAGED, THE SIDE BROOM WILL

AUTOMATICALLY ENGAGE WHEN LOWERED.

SIDE BROOM ADJUSTMENT (See figure 9)

The side broom lever has an adjustment for changing the sweep height to compensate for broom wear. The side broom adjustment is located under the right side of the instrument panel.

	C1641batt	FIGURE 9	MAIN BROOM LEVER (See figure 10)
			MAIN BROOM LEVER (See figure 10)
			The main broom lever is located on the left side of the
			instrument panel. The main broom lever has three posi-
			tions and controls the main broom sweep height.
	MAIN		To lower the main broom, grasp the lever and move it to
	BROOM		the left out of the “UP” position, and place it in the
	LEVER		“SWEEP” or “FLOAT” position.
	LEVER
			The “SWEEP” position is used for normal sweeping and
			should be used under most sweeping conditions (approxi-
			mately 2” broom pattern).
			The “FLOAT” position is used for sweeping very uneven
			surfaces only. Using the float position will cause premature
			wear on the main broom if used under normal operating
			conditions for extended periods of time (approximately 4”
	MAIN		broom pattern).
	MAIN		CIRCUTBREAKERS
	BROOM		NOTE
	ADJUSTMENT		The Main Broom will automatically engage when lowered to
			the sweep position or the float position. The hopper must be
			completely closed.
			MAIN BROOM ADJUSTMENT (See Figure 10)
			The main broom lever has an adjustment for changing the
			sweep height to compensate for broom wear. The main
	C1642-1batt	FIGURE 10	broom adjustment is located under the left side of the
	C1642-1batt	FIGURE 10	instrument panel.
			instrument panel.
	1-18		American-Lincoln
			ATS 46-53 Battery

Image 18

Nilfisk-ALTO 46/53 manual Side Broom Lever, Main, SIDE BROOM LEVER See Figure, SIDE BROOM ADJUSTMENT See figure

Contents

American-Lincoln Technology ATS 46/53 BATTERYPARTS LIST OPERATOR’STABLE OF CONTENTS ATS 46-53BatteryAmerican-Lincoln SERVICE PRECAUTIONS ATS 46/53 BatterySERVICE CHART SERVICE INSTRUCTIONSCHAPTER 3 OPTIONS WEIGHT CLEANING PATHDIMENSIONS TRAVEL SPEEDTANKS WARRANTYSQUEEGEE HOPPERAmerican-Lincoln MACHINE DIMENSIONSATS 46/53 Battery 65.41 cmThe torque tolerance is ± on torque values STANDARD HARDWARE & TORQUE VALUESHYDRAULIC TORQUE REQUIREMENTS Decimal DECIMAL-METRICCONVERSION TABLEFraction MillimeterMACHINE PREPARATION PREPARING THE MACHINE FOR OPERATIONSAFETY INSTRUCTIONS DANGERREAD THE INSTRUCTION BOOK ATS 46/53 Battery American-Lincoln1-13 ATS 46-53Battery 1-14American-Lincoln LIGHT SWITCH See Figure OPERATION OF CONTROLS AND GAUGESHORN BUTTON See Figure CONDITION HOURMETER KEY SWITCH See FigureTO ENGAGE THE SAFETY ARM FILTER SHAKER SWITCH See FigureHOPPER SAFETY LOCK ARM See Figure C1700SIDE BROOM LEVER SIDE BROOM ADJUSTMENT See figureMAIN BROOM ADJUSTMENT See Figure MAINDUST CONTROL SWITCH See Figure SCRUB DECK SWITCHSWITCH SCRUB DECK SWITCH See FigureRECYCLING OR ESP & AUTOFIL SYSTEM SOLUTION CONTROL See FigureNON-RECYCLINGOR STANDARD SCRUBBING SYSTEM TO DISCONNECT WATER HOSEOPERATION OF CONTROLS AND GAUGES BRAKE PARKINGFOOT PEDAL FOOT PEDAL ACCELERATORHOPPER LIFT LEVER - See Figure HOPPER DUMP DOOR LEVER - See FigureSWITCH TURN SIGNALSWITCH TURN SIGNAL - 4-WayOption See FigureFILTER PANEL LATCH See Figure C1719C1718 FRONT COVER LATCH See FigureMAIN BROOM HYDRAULIC RESERVOIR LEVEL SIGHT GAUGEMAIN BROOM COMPARTMENT DOORS See Figure COMPARTMENTHOPPER DOOR LEVER See Figure HOPPER LIFT LEVER See FigureHOPPER FILTER COVER See Figure THE ESP RECYCLING CONTROL PANEL See Figure THE ESP RECYCLING SYSTEM ON/OFF SWITCHSOLUTION LEVEL WARNING LIGHT DETERGENT LOW WARNING LIGHTRECOVERY SOLUTION TANKDETERGENT TANK SOLUTION TANK RECOVERYORIFICE SWEEPING AND DUST CONTROL SYSTEMS-HOWTHEY WORK PRE-STARTCHECKLISTSTARTING BATTERY MACHINES DUST CONTROLSTORAGE FOR BATTERY-POWEREDMACHINES POST-OPERATIONCHECKLISTBATTERY CHARGING INSTRUCTIONS EMPTYING THE DEBRIS HOPPERHELPFUL HINTS FOR CLEANING OPERATION MAIN AISLE100 HOUR MAINTENANCE CHECKLIST SERVICE CHART50 HOUR WEEKLY MAINTENANCE CHECKLIST 250 HOUR MAINTENANCE CHECKLISTPage SERVICE PRECAUTIONS SERVICE PRECAUTIONSMAIN BROOM LEVEL ADJUSTMENT SWEEPING SYSTEM SERVICE MAIN BROOMADJUSTING THE MAIN BROOM HEIGHT CHECKING THE MAIN BROOM SWEEP PATTERNSIDE BROOM SERVICE SIDE BROOM SERVICEADJUSTING THE SIDE BROOM HEIGHT SIDE BROOMCLEANING THE DUST CONTROL FILTER HOPPER SERVICECLEANING THE HOPPER HOPPERREPLACING THE DUST CONTROL FILTER DUST FLAPSADJUSTING THE BRAKES BRAKE SERVICEADJUSTING THE BRAKE PEDAL BRAKESFILL HYDRAULIC RESERVOIR GENERAL MACHINE MAINTENANCECLEANING THE HYDRAULIC SYSTEM FILLING THE HYDRAULIC RESERVOIRSOLUTION CONTROL Non-Recyclingor Standard SOLUTION LOW WARNING LIGHTRECOVERY HIGH WARNING LIGHT SOLUTION CONTROL Recycling or ESP SystemRECYCLING PUMP ESP SYSTEM To service the bladesADJUSTING CASTERS RECYCLING PUMP STORAGEBATTERY PARTS LIST LEGEND ABBREVIATIONS - SCREWSABBREVIATIONS - SETSCREWS REMEDY PROBLEMPROBABLE CAUSE GENERAL TROUBLESHOOTINGREMEDY PROBLEMPROBABLE CAUSE 1. Worn scrubbing brushesORDERING PARTS