2

functions shooting and Focusing

58

Setting the focal length

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

 

 

 

 

By setting the focal length of the lens in advance, you can

 

 

 

 

 

j

 

 

 

 

 

 

 

 

 

use the image stabilizer function with lenses other than

 

 

 

 

 

 

 

 

 

 

Micro Four Thirds/Four Thirds system lenses. This setting

 

 

 

 

 

 

 

 

 

is deactivated when a Micro Four Thirds/Four Thirds

 

 

 

 

 

 

 

IS 1

 

system lens is attached.

 

 

 

 

 

 

 

FOCAL LENGTH

F

 

 

 

1 Press the Fbutton when the image stabilizer is

 

 

 

 

AUTO

 

L F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

turned on.

 

 

 

 

 

 

 

 

 

 

 

50mm

 

2 Use the sub dial to set the focal length and press

 

 

 

 

 

 

 

 

 

i.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Focal lengths that can be set

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8mm

10mm

12mm

16mm

18mm

21mm

 

24mm

 

28mm

30mm

35mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

40mm

48mm

50mm

55mm

65mm

70mm

 

75mm

 

80mm

85mm

90mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100mm

105mm

120mm

135mm

150mm

180mm

 

200mm

 

210mm

250mm

300mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

350mm

400mm

500mm

600mm

800mm

1,000mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• If the focal length of the lens you are using is not listed, select the closest value.

xNotes

•The image stabilizer cannot correct excessive camera shake or camera shake that occurs when the shutter speed is set to the slowest speed. In these cases, it is recommended that you use a tripod.

•When using a tripod, set [IMAGE STABILIZER] to [OFF].

•When using a lens with an image stabilization function, turn off the image stabilizer function of either the lens or the camera.

•If [IMAGE STABILIZER] is set to [I.S.1], [I.S.2] or [I.S.3] and you turn off the camera, the camera will vibrate. This is due to the camera initializing the image stabilizer mechanism.

•You may notice an operating sound or vibration when the image stabilizer is activated.

•If the image stabilizer icon blinks in red on the monitor, it indicates a failure of the image stabilizer function. If you take a picture as is, the composition may be off. Consult your Olympus Authorized Service Center.

•The image stabilizer will not activate at shutter speeds of over 2 seconds.

•If the internal temperature of the camera exceeds the specified temperature, the image stabilizer is deactivated and the image stabilizer icon lights red on the monitor.

EN