Omron Healthcare VARISPEEDF7 specifications User Parameter, EN-18

User Parameter

Param-
eter	Name	Description
Num-
ber
Initialize Data
	Language	0:English
	selection for
		2:German
	Digital Opera-
A1-00		3:French
	tor dis-	4:Italian
	play(JVOP-	5:Spanish
		6:Portuguese
	160-OY only)
		0:Monitoring only (Monitoring drive
		mode and setting A1-01 and A1-04.)
		1:Used to select user parameters (Only
	Parameter	parameters set in A2-01 to A2-32 can
A1-01		be read and set.)
	access level	2:Advanced
		(Parameters can be read and set in
		both, quick programming mode (Q)
		and advanced programming mode
		(A).
	Control method	0:V/f control
A1-02		1:V/f control with PG
	selection	2:Open loop vector control
		3:Closed loop vector control
		0: No initializing
		1110:Initializes using the user
		parameters
A1-03	Initialize	2220:Initializes using a two-wire
		sequence. (Initializes to the factory
		setting.)
		3330: Initializes using a three-wire
		sequence.
Sequence / Reference Source
		Sets the frequency reference input
	Reference	method.
b1-01	source selec-	0:Digital Operator
	tion	1:Control circuit terminal (analog input)
		2:Serial communication (RS422 / 485)
		3:Option Card
	RUN com-	Sets the run command input method.
		0:Digital Operator
b1-02	mand source
		1:Control circuit terminal (digital inputs)
	selection	2:Serial communication (RS422 / 485)
		3:Option Card
		Selects the stopping method when the
		Run signal is removed
	Stopping	0:Deceleration to stop
b1-03	method selec-	1:Coast to stop
	tion	2:DC injection to stop
		3:Coast to stop with timer (New Run
		commands are disregarded while
		coasting.)
		0:Reverse enabled
	Prohibition of	1:Reverse disabled
b1-04	reverse opera-	2:Output Phase Rotation (both rota-
		tional directions are enabled)
	tion
		3:Output Phase Rotation with Reverse
		disabled.
Acceleration / Deceleration Settings
C1-	Acceleration/	Sets the time to accelerate/decelerate
	Deceleration	from 0 Hz to the maximum output fre-
††
	times	quency.
S-Curve Settings
C2-	S-curve char-	Sets the S-curve characteristic at accel-
	acteristic time
††		eration start and end.
	at acceleration

Param-
eter	Name	Description
Num-
ber

Motor Slip Compensation (not available in V/f with PG)

		Used to improve speed accuracy
C3-01	Slip compensa-	• Increase if output frequency is too low
	tion gain	• Decrease if output frequency is too
		high.
	Slip compensa-	Sets the slip compensation delay time
	tion delay time	• Increase if output frequency is not
C3-02		stable
	(only available	• Decrease setting when slip compen-
	in V/f and OLV)
		sation responsiveness is low.

Speed Control (ASR) (only available in V/f with PG and CLV)

C5-01	ASR propor-	Sets the proportional gain of the speed
	tional gain 1	loop (ASR)
C5-02	ASR integral	Sets the integral time of the speed loop
	time 1	(ASR)
C5-03	ASR propor-	P,I
				P = C5-01
	tional gain 2			I = C5-02
				P = C5-03
	ASR integral			I = C5-04
C5-04
	time 2	0	E1-04	Motor
				speed (Hz)
C5-06	ASR delay time	Sets the ASR filter time constant.
	(only CLV)
	ASR switching	Sets the frequency for switching
C5-07	frequency	between ASR gain 1, 2 and ASR integral
	(only CLV)	time 1, 2
	ASR integral	Sets the limit for the integral part of the
C5-08	limit
		ASR controller.
	(only CLV)
Carrier	Frequency
	Heavy/Normal	0:Heavy Duty
C6-01		1:Normal Duty 1
	duty selection	2:Normal Duty 2
		Selects the carrier frequency (factory
		setting depends on Inverter		capacity)
	Carrier fre-	0: Low noise, low carrier
		1: 2.0 kHz
C6-02	quency selec-	2: 5.0 kHz
	tion	3: 8.0 kHz
		4: 10.0 kHz
		5: 12.5 kHz
		6: 15.0 kHz
		F: Programmable pattern
Speed	Settings
d1-01	Multi speed
to	references 1 to
d1-16	16	Sets the multi-step speed references.
d1-17	Jog frequency
	reference
Torque	Control (only	available in CLV)
d5-01	Torque control	0:Speed control
	selection	1:Torque control
	Speed/torque	Sets the delay from inputting a “speed/
		torque control change” signal (by digital
d5-06	control switch
		input) until the control is acutally
	over timer
		changed
V/f Pattern Settings
E1-01	Input voltage	This setting is used as a reference value
	setting	for protection functions.

EN-18