Onkyo HT-RC370 Surround Back Ch, LPF of LFE Low-PassFilter for the LFE Channel, Double Bass, Unit

Note

*1	“Full Band” can be selected only when “Full Band” is
	selected in the “Front” setting.
*2	If the “Surround” setting is set to “None”, this setting cannot
	be selected.
*3	If the “Surround” setting is set to anything other than “Full
	Band”, “Full Band” cannot be selected here.
*4	If the “Speakers Type(Front)” setting is set to “Bi-Amp”, or
	the “Powered Zone 2” setting is set to “Yes”, this setting
	cannot be selected.

■Surround Back Ch

`1ch:

Select if only one surround back speaker L is connected.

`2ch:

Select if two (left and right) surround back speakers are connected.

Note

•If the “Surround Back” Setting is set to “None”, this setting cannot be selected.

■LPF of LFE

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 120Hz

`Bypass:

Low-Pass Filter is not applied.

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

Note

• If you’re using THX-certified speakers, select “80Hz”.

■Double Bass

This setting is NOT set automatically by

Audyssey MultEQ® XT Room Correction and Speaker Setup function (➔ page 31).

`On

`Off(THX)

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.

Note

•This function can be set only if the “Subwoofer” setting is set to “Yes”, and the “Front” setting is set to “Full Band”.

•If you’re using THX-certified speakers, select “Off(THX)”.

■Subwoofer Phase

`0º

`180º:

Moves the subwoofer phase.

Note

•If the “Subwoofer” setting is set to “No”, this setting cannot be selected (➔ page 46).

■Wireless Subwoofer

When an optional unit is connected to the UNIVERSAL PORT jack on the AV receiver, the speaker setting menu may appear on screen.

`Yes:

The audio is output from the speakers connected to the wireless unit.

`No:

The audio is not output from the speakers connected to the wireless unit.

When the wireless unit is connected to the UNIVERSAL PORT jack on the AV receiver, you can select if you wish to output the audio from the speakers connected to the wireless unit.

Note

•If the “Subwoofer” setting is set to “No”, this setting cannot be selected (➔ page 46).

Speaker Distance

This setting is set automatically by

Audyssey MultEQ XT Room Correction and Speaker Setup function (➔ page 31).

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

■Unit

`feet:

Distances can be set in feet. Range: 0.5ft to 30.0ft in

0.5foot steps.

`meters:

Distances can be set in meters. Range: 0.15m to 9.00m in 0.15 meter steps.

(The default setting varies from country to country.)

■Left, Front Wide Left, Front High Left, Center, Front High Right, Front Wide Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left, Subwoofer

`Specify the distance from each speaker to your listening position.

Note

•These settings are not available in either of the following cases:

–a pair of headphones is connected.

–the “Audio TV Out” setting is set to “On” (➔ page 58).

–“HDMI Control(RIHD)” is set to “On” (➔ page 57) and you’re listening through your TV speakers.

•Speakers that you set to “No” or “None” in the

“Speaker Configuration” cannot be selected (➔ page 46).

En

47