■Speakers Type
`Normal:
Select this if you’ve connected your front speakers normally.
`
Select this if you’ve
Note
•Powered Zone 2 cannot be used if “Speakers Type” is set to
■Speaker Terminal Assign Front High/Front Wide/Zone2
With this setting, you can specify the speakers con- nected to FRONT HIGH OR FRONT WIDE OR ZONE 2 SPEAKERS terminals.
`Front High:
Front high speakers can be used.
`Front Wide:
Front wide speakers can be used.
`Zone2:
Zone 2 speakers can be used. (Powered Zone 2 enabled).
Note
•If the “Speakers Type” setting is set to
SurrBack/Front High/Front Wide
With this setting, you can specify the speakers con-
nected to SURR BACK OR FRONT HIGH OR FRONT WIDE SPEAKERS terminals.
`Surr Back:
Surround back speakers can be used.
`Front High:
Front high speakers can be used.
`Front Wide:
Front wide speakers can be used.
Note
•If the “Speakers Type” setting is set to
•If “Front High” is selected in the “Front High/Front Wide/ Zone2” setting, you cannot select “Front High” here.
•If “Front Wide” is selected in the “SurrBack/Front High/ Front Wide” setting, you cannot select “Front Wide” here.
Speaker Configuration
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify “Full Band” for speakers that can output low fre- quency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover fre- quency will be output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequencies. If you set up your speak- ers using Audyssey 2EQ® Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to “80Hz(THX)” crossover.
■Subwoofer
`Yes:
Select if a subwoofer is connected.
`No:
Select if no subwoofer is connected.
■Front
`Full Band
`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
Note
•If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”.
■Center*1, Surround*1, Surr Back*2*3*4*5
`Full Band
`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
`None:
Select if no speaker is connected.
■Front Wide*1*2*4*6, Front High*1*2*4*7
`Full Band
`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
`None:
Select if no speaker is connected.
Note
*1 “Full Band” can be selected only when “Full Band” is selected in the “Front” setting.
*2 If the “Surround” setting is set to “None”, this setting cannot be selected.
*3 If the “Surround” setting is set to anything other than “Full Band”, “Full Band” cannot be selected here.
*4 If the “Speakers Type” setting is set to
*5 If you have selected other than “Surr Back” in the “Surr- Back/Front High/Front Wide” setting, this setting cannot be selected.
*6 If you have selected other than “Front Wide” in the “Front High/Front Wide/Zone2” or “SurrBack/Front High/Front Wide” setting, this setting cannot be selected.
*7 If you have selected other than “Front High” in the “Front High/Front Wide/Zone2” or “SurrBack/Front High/Front Wide” setting, this setting cannot be selected.
■Surr Back Ch
`1ch:
Select if only one surround back speaker L is con- nected.
`2ch:
Select if two (left and right) surround back speakers are connected.
Note
•If the “Surr Back” Setting is set to “None” (➔ 48), this setting cannot be selected.
En
41