Onkyo SR608 Only the front speakers produce sound, Only the center speaker produces sound

■Only the front speakers produce sound

When the Stereo or Mono listening mode is selected,	—
only the front speakers and subwoofer produce
sound.
In the Mono listening mode, only the front speakers	44
output sound if the “Output Speaker” setting is set
to “Left/Right”.
Check the Speaker Configuration.	41

■Only the center speaker produces sound

If you use the Dolby Pro Logic IIx Movie, Dolby Pro — Logic IIx Music, or Dolby Pro Logic IIx Game lis- tening mode with a mono source, such as an AM radio station or mono TV program, the sound is con- centrated in the center speaker.

In the Mono listening mode, only the front speakers	44
output sound if the “Output Speaker” setting is set
to “Center”.
Make sure the speakers are configured correctly.	41

■The surround speakers produce no sound

When the T-D (Theater-Dimensional), Stereo or	—
Mono listening mode is selected, the surround
speakers produce no sound.
Depending on the source and current listening mode,	—
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
Make sure the speakers are configured correctly.	41

■The center speaker produces no sound

When the Stereo or Mono listening mode is selected,	—
the center speaker produces no sound.
In the Mono listening mode, only the front speakers	44
output sound if the “Output Speaker” setting is set
to “Left/Right”.
Make sure the speakers are configured correctly.	41

■The front high, front wide and surround back speakers produce no sound

Depending on the current listening mode, no sound 33 may be produced by the front high, front wide and surround back speakers. Select another listening mode.

Not much sound may be produced by the front high,	—
front wide and surround back speakers with some
sources.
Make sure the speakers are configured correctly.	41
While Powered Zone 2 is being used, playback in the	55
main room is reduced to 5.1-channels and the front
high, front wide and surround back speakers produce
no sound.

■The subwoofer produces no sound

When you play source material that contains no	—
information in the LFE channel, the subwoofer pro-
duces no sound.
Make sure the speakers are configured correctly.	41

■There’s no sound with a certain signal format

Check the digital audio output setting on the con-	—
nected device. On some game consoles, such as
those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an — audio output format from a menu.

Depending on the input signal, some listening modes 33–37cannot be selected.

■Can’t select the Pure Audio listening mode

(European, Australian and Asian models) The	—
Pure Audio listening mode cannot be selected while
Zone 2 is on.

■ Can’t get 6.1/7.1 playback

If no surround back speakers, front wide and front	—
high speakers are connected, or the Zone 2 speakers
are being used, 6.1/7.1 playback is not possible.
You can not always select all of the listening modes,	33–37
depending on the number of the speakers connected.

■The speaker volume cannot be set as required (The volume cannot be set to +18.0 dB)

Check to see if a maximum volume has been set.	50
If the volume level of each individual speaker has	25, 42

been adjusted to high positive values, then the maxi- mum master volume possible may be reduced. Note that the individual speaker volume levels are set automatically after the Audyssey 2EQ® Room Cor- rection and Speaker Setup function has been com- pleted.

■ Noise can be heard

Using cable ties to bundle audio cables with power — cords, speaker cables, and so on may degrade the audio performance, so don’t do it.

An audio cable may be picking up interference. Try — repositioning your cables.

■ The Late Night function doesn’t work

Make sure the source material is Dolby Digital,	53
Dolby Digital Plus, and Dolby TrueHD.

■ About DTS signals

When DTS program material ends and the DTS bit- — stream stops, the AV receiver remains in DTS listen- ing mode and the DTS indicator remains on. This is

to prevent noise when you use the pause, fast for- ward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback.

With some CD and LD players, you won’t be able to — playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate,

or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

When playing DTS program material, using the	—
pause, fast forward, or fast reverse function on your
player may produce a short audible noise. This is not
a malfunction.

En

67