Onkyo TX-NR5010 instruction manual En-104, Remote Controller, RI Dock for iPod/iPhone

Remote Controller

■The remote controller doesn’t work

Before operating this unit, be sure to press	—
RECEIVER.
Make sure that the batteries are installed with the	5
correct polarity.
Install new batteries. Don’t mix different types of	5
batteries, or old and new batteries.
Make sure that the remote controller is not too far	5
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor.
Make sure that the AV receiver is not subjected to	—
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
If the AV receiver is installed in a rack or cabinet	—
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
Make sure you’ve selected the correct remote	12, 96
controller mode.
When using the remote controller to control other	—
manufacturers’ AV components, some buttons may
not work as expected.
Make sure you’ve entered the correct remote control	95
code.
Make sure to set the same ID on both the AV receiver	86
and remote controller.

■ Can’t control other components

If it’s an Onkyo component, make sure that the u 25 cable and analog audio cable are connected properly. Connecting only an ucable won’t be enough.

Make sure you’ve selected the correct remote	12, 96
controller mode.
If you’ve connected an cassette tape deck to the	54

TV/CD IN jack, or an RI Dock to the TV/CD IN or GAME 1 IN jacks, for the remote controller to work properly, you must set the input display appropriately.

If you cannot operate it, you will need to enter the	94
appropriate remote control code.
To control another manufacturer’s component, point	95
the remote controller at that component.
To control an Onkyo component that’s connected via	96
u, point the remote controller at the AV receiver.
Be sure to enter the appropriate remote control code
first.
To control an Onkyo component that’s not connected	96
via u, point the remote controller at the component.
Be sure to enter the appropriate remote control code
first.
The entered remote control code may not be correct.	—
If more than one code is listed, try each one.

■Can’t learn commands from another remote controller

When learning commands, make sure that the 99

transmitting ends of both remote controllers are pointing at each other.

Are you trying to learn from a remote controller that — cannot be used for learning? Some commands

cannot be learned, especially those that contain several instructions.

RI Dock for iPod/iPhone

■ There’s no sound

Make sure your iPod/iPhone is actually playing.	—
Make sure your iPod/iPhone is properly inserted in	—
the Dock.
Make sure the AV receiver is turned on, the correct	—
input source is selected, and the volume is turned up.
Make sure the plugs are pushed in all the way.	—
Try resetting your iPod/iPhone.	—

■ There’s no video

Make sure that your iPod/iPhone model’s TV OUT — setting is set to On.

En-104

Appendix

Make sure the correct input is selected on your TV or — the AV receiver.

Some versions of the iPod/iPhone do not output	—
video.

■The AV receiver’s remote controller doesn’t control my iPod/iPhone

Make sure your iPod/iPhone is properly inserted in	—
the Dock. If your iPod/iPhone is in a case, it may not
connect properly to the Dock. Always remove your
iPod/iPhone from the case before inserting it into the
Dock.
The iPod/iPhone cannot be operated while it’s	—
displaying the Apple logo.
Make sure you’ve selected the right remote mode.	93
When you use the AV receiver’s remote controller,	—
point it toward your AV receiver.
If you still can’t control your iPod/iPhone, start	—
playback by pressing your iPod/iPhone model’s Play
button. Remote operation should then be possible.
Try resetting your iPod/iPhone.	—
Depending on your iPod/iPhone, some buttons may	—
not work as expected.

■The AV receiver unexpectedly selects my iPod/iPhone as the input source

Always pause iPod/iPhone playback before selecting — a different input source. If playback is not paused, the Direct Change function may select your iPod/iPhone

as the input source by mistake during the transition between tracks.

■iPod/iPhone doesn’t work properly

Try reconnecting your iPod/iPhone. —