Tuning in a radio station

TUNING ®

DIRECT TUNING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MASTER VOLUME

STANDBY/ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PARAMETER SELECTOR

 

 

 

 

 

 

 

 

 

STANDBY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER

 

KEY CONTROL

VOCAL

 

 

 

 

 

 

 

 

 

 

 

 

 

PARAMETER CONTROLLER

 

 

 

 

 

 

 

CANCEL

SCAN

GROUP

1

2

3

4

5

6

7

8

9

0 /10

DIRECT TUNING

TUNING

 

 

ON

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

MIC LEVEL

2

ECHO LEVEL

A SPEAKERS

B

 

SURROUND MODE

 

MIDNIGHT THEATER

 

Re-EQ

 

 

MEMORY FM MUTE/MODE

 

KARAOKE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLEAR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BASS

TREBLE

 

MIN

MAX

MIN

MAX

MIN

MAX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C D

 

PHONES

1

 

MIC

2

3-D BASS

MULTI CH INPUT

DVD

VIDEO 1

VIDEO 2

 

TAPE(MONITOR)

FM

 

AM

 

PHONO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A/V KARAOKE CONTROL RECEIVER TX-SE550

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FM

 

 

 

 

 

 

 

Number buttons

 

 

 

 

AM

FM MUTE/MODE

1

 

 

 

 

 

 

FM

 

AM

 

 

SPEAKERS A

 

 

SPEAKERS A

 

 

2

TUNING

SPEAKERS A

FM MUTE

TUNED

FM STEREO

VIDEO

2

 

 

 

 

 

 

 

 

 

 

 

 

MHz

1

 

 

 

 

 

 

FM

 

AM

 

 

SPEAKERS A

 

 

SPEAKERS A

 

 

2

DIRECT TUNING

SPEAKERS A

FM MUTE

VIDEO

2

MHz

3

1 2 3 4 5 6 7 8 9 0 /10

SPEAKERS A

FM MUTE TUNED FM STEREO

 

VIDEO 2

 

MHz

 

 

Manual tuning

1.Press the FM or AM button.

2.Use the TUNING /® buttons to change the frequency.

® (up) ..............the frequency increases.

(down) .........the frequency decreases.

The frequency changes in 50 kHz steps in FM and 10 kHz (or 9 kHz) in AM each time you press the TUNING /® button.

In FM, if this button is held continuously for more than 0.5 sec- onds, the frequencies are scanned automatically (FM auto tun- ing mode). When a broadcast is received, scanning stops.

Direct tuning

1. Press the FM or AM button.

2. Press the DIRECT TUNING button.

The “_ _” will flash 16 seconds in the frequency display.

3. Enter the frequency using the number buttons while the cursor is flashing.

Example: 88.10 MHz

50 kHz step area, 8 8 1 0/10 100 kHz step area, 8 8 1

Use the 0/10 number button to enter a 0.

Out-of-range frequencies will be ignored.

When receiving AM broadcasts with a 10 kHz steps, entering a number for the 10 kHz digit will set the 1 kHz digit to 0.

Receiving RDS (European model only)

When an RDS (Radio Data System) station broadcasting PS (Pro- gram Service Name) information is received, the RDS indicator lights up and the name of the station is displayed.

RDS reception is only available on the European model, and only in areas where RDS broadcasts are available.

MEMORY FM MUTE/MODE

CLEAR

Listening to a stereo radio station (FM mode)

When you tune in a stereo FM station, the FM STEREO indicator lights up if the signal is sufficiently strong.

If the signal is weak, it may be impossible to tune in to the desired station. In this case, tune in as follows.

Press the FM MUTE/MODE button. The FM MUTE indicator turns off. At this time, the station will be in mono and interstation noise will be heard. Select the station to which you want to listen.

24

Page 24
Image 24
Onkyo TX-SE550 appendix Tuning in a radio station, Manual tuning, Direct tuning, Receiving RDS European model only