Onkyo TX-SR600/600E instruction manual Front panel facilities, TX-SR700/700E

Front panel facilities

For further operational instructions, see the pages indicated in	FM MODE button [40]
brackets [ ].	Press to change the stereo mode from AUTO to MONO and vice
POWER switch (for all models other than USA and	versa. Each time this button is pressed, the AUTO indication turns
	on and off indicating the current mode. If you are listening to an FM
Canadian models) [33]	radio station in stereo and the sound cuts out or there is a great deal of
Press to turn on and off the main power supply for the TX-SR700/	noise, switch from AUTO to MONO.
700E/600/600E. When the TX-SR700/700E/600/600E is turned on
with the POWER switch, the STANDBY indicator lights.	Remote control sensor [7]
• Before turning on the power, check to make sure that all cords
are properly connected.	AUDIO ADJUST button [57]
• When the power is turned on, a sudden surge of current will
	Press to adjust the sound quality and the listening mode.
occur that may adversely affect the operation of other devices.
To prevent this, do not plug the TX-SR700/700E/600/600E into	MENU button [36]
the same circuit used by sensitive equipment, e.g., computers.
	Press to enter the Setup Menu. The OSD Menu will appear on the TV
STANDBY/ON button [33]	monitor as well as the front display on the TX-SR700/700E/600/
If pressed with the POWER switch turned on (with the receiver	600E.
plugged in for US models), the TX-SR700/700E/600/600E turns on	RETURN button [36]
and the display lights up. If pressed again, the TX-SR700/700E/600/
600E returns to the standby state. In the standby state, the display is	When in the Setup Menu, press to go back one level. If pressed while
turned off and the TX-SR700/700E/600/600E cannot be operated.	at the Main Menu, you will exit the Setup Menu.
STANDBY indicator [7, 33]	TUNING	/	, PRESET / , cursor		( / / / )
Lights when the TX-SR700/700E/600/600E is in the standby state	buttons [36, 40, 41]
and when a signal is received from the remote controller.	To tune into a radio station, press the TUNING			/	buttons. The
	tuner frequency is displayed in the front display and it can be changed
DISPLAY button [48]	in 50-kHz increments for FM and 10-kHz (or 9-kHz) increments for
Press to display information about the current input source signal.	AM.
	When FM is selected as the input source, you can hold down either
Each time you press the display button, the screen changes to show
	the TUNING or	button and then release it to activate the auto-
you different information concerning the input signal.
	search feature. It will search for a station in the direction of the
RT/PTY/TP (European models only) button [43]	button you pressed and stop when it tunes into one. When navigating
	through the menu settings, these buttons move the cursor up or down
This button is only available on European models. Press this button	(or change the highlighted item).
to tune into the Radio Data System (RDS) for FM broadcasting. RDS	To select a radio station that was stored using the MEMORY button,
was developed within the European Broadcasting Union (EBU) and	press the PRESET	/	buttons.
is available in most European countries. Each time the button is	When navigating through the menu settings, these buttons select the
pressed, the display changes from RT (radio text) to PTY (program	value or item that you selected with the TUNING			/	buttons.
type) to TP (traffic program) and then back to RT again.	When you press the MENU button, the TUNING and PRESET
	buttons become cursor buttons to be used for Setup Menu
DIMMER button	operations.
Press to set the brightness of the front	ENTER button [36]
display. There are 3 settings available:
normal, dark, and very dark.	Press to display the screen for the item that is selected in the Setup
	Menu.
• The brightness of the front display can
also be performed using the remote	MASTER VOLUME dial [44, 45]
controller.
	TX-SR600/600E:
LISTENING MODE buttons [49-51]	Use to control the volume.
Press these buttons to select a listening mode for the current input	TX-SR700/700E:
	Use to control the volume in the main zone. The volume for the
source. Press the DIRECT, STEREO, and SURROUND buttons to
	remote zone (Zone 2) is independent.
select a listening mode directly. Press the DSP button to select any of
the possible listening modes for the input source currently selected.
Note:	VIDEO 4 INPUT terminals [21, 28]
During playback of a multichannel source, press the DIRECT button	For connecting a video camera or game device.
to turn off the tone control and the SURROUND button to turn on	The VIDEO 4 INPUT (DIGITAL)
the tone control. [48]	jack is provided with a protective
	cap. When using this jack, remove
Front display	the protective cap and keep it
	safely. When not using this jack,
MEMORY button [41]	replace the protective cap.
Press to assign the radio station that you are currently tuned into to a
			Protective cap
preset channel or press to delete a previously preset station.

9