Panasonic AV-HS400AE Caution for AC Mains Lead

3

indicates safety information.

Safety precautions

Caution for AC Mains Lead

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This product is equipped with 2 types of AC mains cable. One is for continental Europe, etc. and the other

one is only for U.K.

Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.

FOR CONTINENTAL EUROPE, ETC.

Not to be used in the U.K. FOR U.K. ONLY

FOR U.K. ONLY

This appliance is supplied with a moulded three pin

mains plug for your safety and convenience.

A 13 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure

that the replacement fuse has a rating of 13 amps

and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark  or the BSI mark  on

the body of the fuse.

If the plug contains a removable fuse cover you must

ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used

until a replacement cover is obtained.

A replacement fuse cover can be purchased from

your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE

FOR THE SOCKET OUTLET IN YOUR HOME

THEN THE FUSE SHOULD BE REMOVED AND

THE PLUG CUT OFF AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL

SHOCK IF THE CUT OFF PLUG IS INSERTED

INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring

code as shown below.

If in any doubt please consult a qualified electrician.

WARNING: This apparatus must be earthed.

IMPORTANT

The wires in this mains lead are coloured in

accordance with the following code.

Green-and-Yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wire in the mains lead of this

appliance may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows.

• The wire which is coloured green-and-yellow must

be connected to the terminal in the plug which is

marked with the letter E or by the earth symbol 

or coloured green or green-and-yellow.

• The wire which is coloured blue must be connected

to the terminal in the plug which is marked with the

letter N or coloured black.

• The wire which is coloured brown must be

connected to the ter minal in the plug which is

marked with the letter L or coloured red.

How to replace the fuse

1. Open the fuse compartment with a screwdriver.

2. Replace the fuse.

Fuse

Contents

Main 12345678910 AUX PGM/A PST/B FTB PinP DSKCUT AUTO Operating Instructions Multi-format Live Switcher VQTB0343 Model No. AV-HS400AE indicates safety information. WARNING: CAUTION: WARNING: THIS APPARATUS MUST BE EARTHED FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY CAUTION indicates safety information. Caution for AC Mains Lead FOR U.K. ONLY Cd Contents 2. System ..................................................20 3. Basic operations .................................23 Contents 4. Input/output signal settings...............62 5. System settings ..................................84 6. External interfaces ...........................101 Description Features Precautions for use 1-1. Control panel Power indicator [POWER] 2 Alarm indicator [ALARM] 1-2. Crosspoint area 1-3. Wipe area 8 Wipe pattern selector buttons 9 BKGD, KEY pattern selector buttons : Pattern page indicator LEDs Page 1-5. Transition area Page 1-6. LCD menu area L LCD M Rotary encoders [F1] to [F5] Adjust Clip Gain Density Invert 2/9 0.0 100.0 100.0 Off 1-7. Positioner area N Positioner [X/Y] O Rotary encoder [Z] 1-8. SD memory card area 1-9. Rear panel connections area POWER 1 SDI INPUTS 1 Page 2-1. Configuration AV-HS400AE Table of optional boards 2-2. Connections Connections when implementing gen-lock (frame synchronizer OFF) AV-HS400AE Connections when not implementing gen-lock (frame synchronizer ON) Example where the optional board is used AV-HS400AE 3-1. Background transition 3-1-1. Selecting the bus 3-1-2. Selecting the bus mode 3-1-3. Selecting the transition mode 3-1-4. Manual transition (using the fader lever) 3-1-5. Auto transition 3-1-6. Cut transition 3-2. Wipe 3-2-1. Selecting the wipe pattern 3-2-2. Selecting the wipe direction 3-2-3. Wipe decorations (border, soft effect) 3-2-4. Setting the wipe start position 3-2-5. Modifying wipe 3-3. Key HS400A KEY PinP DSK 3-3-1. Selecting the key type 3-3-2. Selecting the key material 3-3-3. Key transitions 3-3-4. Key preview 3-3-5. Adjusting the luminance key and linear key 3-3-6. Adjusting the chroma key Page Page 3-3-7. Key decorations 3-3-8. Masking the key signals 3-3-9. Flying key ABC 3-4. PinP (picture in picture) 3-4-1. Selecting the PinP material 3-4-2. PinP transitions 3-4-3. PinP preview 3-4-4. PinP adjustments SD HD SD 3-4-5. PinP decorations 3-4-6. Trimming settings 3-5. DSK (downstream key) 3-5-1. Selecting the DSK type 3-5-2. Selecting the DSK material 3-5-3. DSK transitions 3-5-4. DSK preview 3-5-5. DSK adjustments 3-5-6. DSK decorations 3-5-7. Masking the DSK signals 3-6. FTB (fade to black) 3-7. Internal colour signals 3-7-1. Setting the colour background 3-8. Freezing the input signals 3-8-1. Displaying the freeze status 3-8-2. Setting freeze 3-9. Switching the AUX output 3-10. Preset memory Page Page 3-11. Frame memories 3-11-1. Transferring images from the AUX bus 3-12. SD memory cards 3-12-1. Initializing the SD memory cards 3-12-2. Saving data on SD memory cards 3-12-3. Loading data from SD memory cards 3-12-4. Deleting files on SD memory cards 3-12-5. Displaying the SD memory card information 4-1. Setting the SDI input signals and analogue input signals 4-1-1. Setting the frame synchronizer 4-1-2. Setting the input mode 4-1-3. Setting the analogue input gain 4-1-4. Setting the analogue composite input signals 4-2. Setting the up-converter (option) 4-3. Setting the DVI input signals (option) 4-3-1. Setting the DVI input signals Page 4-3-2. Adjusting the DVI input signals 4-4. Setting the output signals 4-4-1. Types of output signals 4-4-2. Assigning the output signals 4-5. Setting the sync signals 4-6. Adjusting the output signal phase <Phase adjustment setup> AVDL Range: Range for automatic phase adjustment. <Phases and delay amounts of input/output signals during HD format use> <Phase relationship between input signals and output signals> (for 1080/59.94i format) (Example 1) (Example 2) 4-7. Setting the multi view display 4-7-1. Setting the screen layout Page 4-7-2. Setting the split frame and characters 4-7-3. Setting the tally displays 4-7-4. Changing the material names 4-8. Setting the on-screen display (OSD) 4-9. Setting the DVI output signals (option) 4-10. Setting the ancillary data 4-11. Setting the down-converter 5-1. Selecting the video format 5-2. Setting the crosspoints 5-2-1. Assigning signals to the crosspoints 5-2-2. Setting the crosspoint switching 5-3. Button assignments 5-3-1. Setting the user buttons 5-3-2. Setting the FTB button 5-4. Setting the date and time 5-5. Network settings 5-6. Other settings 5-6-1. Setting the LCD backlight 5-6-2. Setting editor enable 5-6-3. Setting the protocol 5-6-4. Setting the GPI 5-7. Camera control Example of connections (when the unit and a controller are connected) Example of connections (when the unit and a pan-tilt head are connected) Page Page Page 5-8. Status displays 5-8-1. Alarm status displays 5-8-2. Displaying the version information and option information 5-9. Initialization 6-1. RS-422 connector 6-2. GPI connector 6-3. Tally connector Specifications LAN straight cable Connections LAN crossover cable LAN straight cable HUB How to install the software Operation <Transmitting images to the unit> <Transmitting images from the unit> Page Page Page Page Page Page Page 9. Appearance Unit: mm 12345678910 AUX PGM/A PST/B FTB PinP DSKCUT AUTO Specifications Page Standard accessories Optional boards (sold separately)