Contents
Main
Safety precautions
WARNING:
CAUTION:
CAUTION:
Note:
IMPORTANT SAFETY INSTRUCTIONS
Contents
Operating precautions
Precautions for use
Installation precautions
Page
Page
=Guide pin
>Camera mounting screws (U1/4 20UNC)
?Side blank panel
@SDI IN connector [SDI IN]
ALENS I/F (2) connector [LENS I/F (2)]
JY connector [Y]
K1394 connector [1394]
LSDI connector [SDI]
MG/L IN connector [G/L IN]
NPROMPTER IN connector [PROMPTER IN]
$Assembling the pan/tilt head
1Attaching the camera mounting base
2Attaching the rotary arm
Camera Mounting base
3Mounting the tally lamp
$Setting the mounting direction switch
Page
$Installing the pan/tilt head
t
For a stand-alone installation For installation on the ceiling
$Mounting the camera
For a stand-alone installation
For installation on the ceiling
$Attaching the wire
For a stand-alone installation For installation on the ceiling
Replacing the consumable parts
Supply voltage: AC 120 V, 60 Hz Power consumption: 145 W
Page
Page
$Front panel
7IRIS [AUTO/MANU/LOCK] button
8SD CARD slot
9IRIS dial
:ZOOM lever/FOCUS dial
;PAN POSITION indicator
BMEMORY button
CPRESET MEMORY selection buttons [1] to [50]
DLCD panel
EMENU/LIMIT button
FCONT dial
$Rear panel
Page
$Operation method
$List of menu items and settings
PRIORITY (MASTER/SLAVE)
DIRECTION settings (PAN, TILT, ZOOM, FOCUS, IRIS, ROTATION: NORMAL/REVERSE)
TILT RANGE setting (190/300 degrees)
SPEED WITH ZOOM POS. setting (OFF/1/2/3)
PRESET SPEED setting (1 to 25)
IRIS CONTROL setting (BOTH/RP400/CB400)
OPTION SWITCH A to H settings (NOT USE / DEF / WIP / HEATER/FAN / LAMP / OPTION / ND / EXT / AF)
MEMORY LENGTH setting (60s/120s/300s/600s)
CONTROL SELECT MODE setting (INTERLOCK/UN-INTERLOCK)
BUZZER setting (OFF/ON)
AUTO RUN setting (START No., END No., INTERVAL)
SD CARD setting
How to mount the AW-RP400 in a rack
AW-RP400
How to change the position of the connector panel
How to replace the zoom switch
Before replacing the zoom switch, turn off the power.
Page
Supply voltage: DC 12.0 V Power consumption: Approx. 13 W
Page
AW-RC400
Front panel Rear panel
1Power LED
2POWER switch
12 345
>=<?@A ; : 9 B
68 C7
Cable Compensation Unit AW-RC400
;MONITOR1, 2 connectors
<Y/VIDEO IN connectors [1 to 5]
=Pr/C IN connectors [1 to 5]
>Pb IN connectors [1 to 5]
How to mount the AW-RC400 in a rack
Supply voltage: DC 12.0 V Power consumption: Approx. 9 W
Page
Page
2
Page
Page
Page
Page
Connections
Example of system configuration
$Turning on the power
$Setting the movement range (limiters) of the AW-PH400 indoor pan/tilt head
Now proceed with the settings for the AW-RP400 pan/tilt control panel.
$Providing cable compensation for the cameras
Waveform monitor (composite signals) Waveform monitor (component signals)
$Genlock adjustments for the respective cameras
$Video adjustments for the cameras
$Tracing memory settings
Page
$Setting the preset memory data
Page
When an IAS, WAS or VAS lens (analog drive) made by Canon is used
When an IASD, WASD or VASD lens (digital drive) made by Canon is used
When an RD lens made by Fujinon is used
Page
Page
Page
P
