Rotary ring Camera mounting screw U1/4-20UNC | Panasonic AW-PH400P

Roll Unit AW-RL400

Parts and their function

1

2

3

4

1Rotary ring

2Camera mounting screw (U1/4”-20UNC)

After mounting the camera, secure it firmly using this screw.

3Camera mounting plate (A) (B)

Mount the camera on this plate using the camera mounting screws.

5

6

5Roll unit anchoring screw holes

This is where the roll unit is secured to the rotary arm of the pan/tilt head.

6Pan/tilt head connector

Connect this to the OPTION connector on the pan/tilt head using the pan/tilt head connecting cable supplied.

4Camera mounting plate anchoring screws

After mounting the camera on the camera mounting plate, anchor it to the roll unit using these screws.

44

Image 44

Panasonic AW-PH400P manual Rotary ring Camera mounting screw U1/4-20UNC, Camera mounting plate a B, Pan/tilt head connector

Contents

AW-RL400 AW-PH400 AW-RP400 AW-RC400 AW-RL400 Safety precautions FCC Note Important Safety Instructions Contents ≥ Handle the units carefully Operating precautions≥ Do not use the units outdoors ≥ Maintenance Introduction AccessoriesPrecautions for use Installation precautions Parts and their function Rotary head connector panel Pedestal connector panel Pedestal Power ON/OFF switchBottom panel Prompter connector Tally lamp accessory ND/EXT connector ND/EXT @ SDI in connector SDILens I/F 2 connector Lens I/F Option connector Option Connector Y ConnectorSDI connector SDI L in connector G/L For a stand-alone installation For installation on the ceiling$ Assembling the pan/tilt head Attaching the camera mounting base Mounting the tally lamp For installation on the ceiling $ Setting the mounting direction switchFor stand-alone installation $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera ≥ Camera AW-E650, AW-E350 $ Attaching the wire≥ Camera AW-E750 Replacing the consumable parts Supply voltage SpecificationsPower consumption Memo Zoom switch Plug D-SUB 15-pin for tally/INCOM system Rack-mounting adaptors Mounting screws M4!8 mm $ Front panel PAN Position indicator Iris indicator= Zoom indicator Focus indicator Preset Memory selection buttons 1 to PAN/TILT lever/ROTATION control switchMemory button LCD panel EXT Cont IN/OUT connectors Camera Control in from RCB P1 to P5 connectorsTALLY/INCOM connector $ Rear panel Remote connector Control OUT to PAN/TILT Head P1 to P5 connectorsMoni SEL OUT connector Camera Control in from ROP connector Menu settings $ Operation method $ List of menu items and settings Menu item Setting Description Initial value Tilt Range setting 190/300 degrees Speed with Zoom POS. setting OFF/1/2/3Preset Speed setting 1 to Iris Control setting BOTH/RP400/CB400 Option Switch a to H settings Memory Length setting 60s/120s/300s/600s Control Select Mode setting INTERLOCK/UN-INTERLOCK Buzzer setting OFF/ONAuto RUN setting Start No., END No., Interval SD Card setting How to mount the AW-RP400 in a rack How to change the position of the connector panel Before changing the position, turn off the power Secure the zoom switch using the four screws How to replace the zoom switchBefore replacing the zoom switch, turn off the power Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 Front panel Power LED Power switchCable length setting switches 0 to SHORT/LONG selector switch MONITOR1, 2 connectors BAC adaptor storage space Video in connectors 1 to= Pr/C in connectors 1 to Pb in connectors 1 to How to mount the AW-RC400 in a rack Power consumption Approx W Ambient operating temperature Pan/tilt head connecting cable Pan/tilt head connector Rotary ring Camera mounting screw U1/4-20UNCCamera mounting plate a B Roll unit anchoring screw holes Installation When the AW-E750, AW-E650 or AW-E350 is used as the camera When the AW-E655 is used as the camera Camera mounting plate’s screws Performance Supply voltage DC 24 Power consumption Approx WPan/tilt head connector Connections Zoom/focus Control Example of system configuration MONITOR1 MONITOR2 Operating procedures $ Turning on the power $ Providing cable compensation for the cameras $ Genlock adjustments for the respective cameras $ Video adjustments for the cameras$ Tracing memory settings Setting the recording time and number of memories Playing the tracing memory data $ Setting the preset memory data Registering the preset memory dataChanging the tracing memory data Erasing the tracing memory data Playing the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company