Read Me First
For U.S.A.
Federal Communications Commission Radio Frequency Interference Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the Panasonic Service Center or an experienced ra- dio/TV technician for help.
Warning
To assure continued compliance, use only shielded interface cables when connecting to a computer or peripheral. Also, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
FCC RF Exposure Warning: This computer is provided with PC Card slots that could be used with wireless transmitter(s), which will be specifically recommended, when they become available. Other
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
Responsible Party: Matsushita Electric Corporation of America
One Panasonic Way
Secaucus, NJ 07094
Tel
FCC Regulation Notice for modem
This equipment contains a FCC approved modem.
Manufacturer of modem: AMBIT Microsystems Corporation Model No. T60M283.00
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
1.This equipment complies with CFR47 Part 68 rules. On the computer is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If required, this information must be provided to the telephone company.
2. An FCC compliant telephone cord and modular plug is pro- |
| |
vided with this equipment. This equipment is designed to be |
| |
connected to the telephone network or premises wiring using |
| |
a compatible modular jack which is Part 68 compliant. See |
| |
Installation Instructions for details. |
| |
3. The REN is used to determine the quantity of devices which |
| |
may be connected to the telephone line. Excessive RENs on the |
| |
telephone line may result in the devices not ringing in response |
| |
to an incoming call. In most, but not all area, the sum of RENs |
| |
should not exceed five (5.0). To be certain of the number of |
| |
devices that may be connected to a line, as determined by the |
| |
Started | ||
total RENs, contact the local telephone company. | ||
4. If your telephone equipment cause harm to the telephone net- | ||
work, the telephone company will notify you in advice that | ||
temporary discontinuance of service may be required. But if | ||
advice notice isn’t practical, the telephone company will no- | Getting | |
tify the customer as soon as possible. Also, you will be ad- | ||
vised of your right to file a complaint with the FCC if you | ||
believe it is necessary. | ||
5. The telephone company may take changes in it’s facilities, |
| |
| ||
equipment, operations or procedures that could affect the op- |
| |
eration of the equipment. If this happens the telephone com- |
| |
pany will provide advance notice in order for you to make |
| |
necessary modifications to maintain uninterrupted service. |
| |
6. If trouble is experienced with this equipment, for repair or |
| |
warranty information, please contact Matsushita Electric |
| |
Corporation of America at DIAL TOLL FREE |
| |
LAPTOP5 |
| |
to the telephone network, the telephone company may request |
| |
that you disconnect the equipment until the problem is resolved. |
| |
7. There are no user serviceable parts contained in this equipment. |
| |
8. This equipment may not be used on coin service provided by |
| |
the telephone company. Connection to party lines is subject to |
| |
state tariffs. |
| |
9. The Telephone Consumer Protection Act of 1991 makes it |
| |
unlawful for any person to use a computer or other electronic |
| |
device to send any message via a telephone fax machine un- |
| |
less such message clearly contains in a margin at the top or |
| |
bottom of each transmitted page or on the first page of the |
| |
transmission, the date and time it is sent and an identification |
| |
of the business or other entry, or other individual sending the |
| |
message and the telephone number of the sending machine or |
| |
such business, other entity, or individual. In order to program |
| |
this information into your fax software, you should refer to |
| |
the manual of the Fax software being used. |
| |
10.According to the FCC’s electrical safety advisory, we recom- |
| |
mend that you may install an AC surge arrestor in the AC outlet |
| |
to which this equipment is connected. Telephone companies re- |
| |
port that electrical surges, typically lightning transients, are very |
| |
destructive to customer terminal equipment connected to AC |
| |
power sources and that this is a major nationwide problem. |
|
“Caution: To reduce the risk of fire, use only No.26 AWG or larger telecom- munication line cord.”
“ATTENTION: Pour réduire le risque d’incendie, utiliser uniquement des conducteurs de télécommunications 26 AWG ou de section supérieure.”
Notice for the products using LCD
This product uses one or more fluorescent lamps containing a small amount of mercury. It also contains lead in some compo- nents. Disposal of these materials may be regulated in your com- munity due to environmental considerations. For disposal or re-
cycling information please contact your local authorities, or the | |
Electronics Industries Alliance: <http://www.eiae.org/> | 3 |
