Section
03 
Installation
| Section |
Installation | 03 |
This unit
1 Antenna input |
gRed
Connect to terminal controlled by ignition switch (12 V DC).
hBlue/white
Connect to system control terminal of the power amp or
Note
!The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places such as near the heater outlet.
!Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
4
60°
5
1
2
3
English
2 | Fuse (10 A) |
3 | Power cord input |
4 | Rear output |
Power cord
L 
1 R
23
4 |
|
|
| |
|
| 6 |
|
|
|
| 8 |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
F |
|
|
|
|
| 7 |
|
|
|
| 9 |
|
|
| |
|
|
|
|
|
|
|
|
| | ||||||
5 |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| |
|
| a |
|
|
|
| c |
|
| | |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
R |
|
|
|
|
|
| b |
|
|
|
| d |
|
| |
| |
|
|
|
|
|
|
| | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
e
f g h
1To power cord input
2Left
3Right
4Front speaker
5Rear speaker
6White
7White/black
8Gray
9Gray/black
a Green |
b Green/black |
c Violet |
d Violet/black |
e Black (chassis ground) |
Connect to a clean, |
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.
Power amp (sold separately)
Perform these connections when using the optional amplifier.
1
| 2 |
|
|
| | 3 | 4 |
|
| ||
5 |
| 5 |
|
| |
|
|
1System remote control Connect to Blue/white cable.
2Power amp (sold separately)
3Connect with RCA cables (sold separately)
4To Rear output
5Rear speaker
Installation
Important
! Check all connections and systems before final installation.
! Do not use unauthorized parts as this may cause malfunctions.
! Consult your dealer if installation requires drilling of holes or other modifications to the vehi- cle.
! Do not install this unit where:
— it may interfere with operation of the vehi- cle.
!To ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents when installing the unit.
DIN front/rear mount
This unit can be properly installed using either
DIN Front-mount
1 Insert the mounting sleeve into the dashboard.
For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space, use the mounting sleeve that came with the vehicle.
2 Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.
1
2
1Dashboard
2Mounting sleeve
1Nut
2Firewall or metal support
3Metal strap
4Screw
5Screw (M4 × 8)
#Make sure that the unit is installed securely in place. An unstable installation may cause skip- ping or other malfunctions.
DIN Rear-mount
1Determine the appropriate position where the holes on the bracket and the side of the unit match.
2Tighten two screws on each side.
1 
3
2
1Truss screw (5 mm × 8 mm)
2Mounting bracket
3Dashboard or console
f Yellow |
Connect to the constant 12 V supply terminal. |
10
En
— it may cause injury to a passenger as a result of a sudden stop.
3 Install the unit as illustrated.
Use commercially available parts when instal- ling.
En 
11