Panasonic MW-20 operating instructions Using in a wall-mounted state, Wall-mount settings

Using in a wall-mounted state

The specific setting is required to use the main unit in a wall-mounted state. Make the wall-mount settings on the menu and install it on the wall.

Make sure to ask a professional mounter or a dealer for installation/uninstallation.

Notes for installation

zDo not install this unit at the following locations to ensure this unit’s performance and to prevent potential troubles.

–Locations other than vertical walls

–Locations near a sprinkler or a sensor

–Locations near high-voltage lines or power sources

–Locations where wind from a heating device hits the unit

–Locations where the unit is subject to vibration or impact

–Locations near sources of magnetism, heat, vapor, oil smoke, etc.

–Locations of high temperature, such as near ceiling lights (spotlight, halogen light, etc.)

–Locations where there may be water droplet (i.e. under an air conditioner)

–High places where the SD insertion part cannot be reached easily

zUse a proper installation method that suits the structure and material of the installing location.

zUse a cloth, etc. to prevent damage of the product or floor during installation.

zWhen tightening screws, make sure the screws are not loosely-tightened or overtightened.

zSecure safety in the surrounding areas and pay enough attention during installation.

Prepare commercially available screws that match the screw holes of the unit’s bottom face.

Screw hole on the main unit’s bottom face

5 mm (13/64")

11 mm (7/16")

„Recommended type of screw

• 2 screws for wall-mounting

• 2 screws for the fitting for wall-mounting

A length which supports the strength of 5 kg (11.1 lb.) or more must be kept for each screw.

	At least 30 mm (13/16")
	7.4 mm (19/64") to 9.4 mm (3/8")
4 mm	2.2 mm (3/32") to 3 mm (1/8")
(5/32")
	3 mm (1/8") to 4 mm (5/32")

Use commercially available screws with the nominal diameter of 4 mm (5/32") or equivalent which are suitable for materials of the wall (i.e. wood, steel, concrete, etc.)

Note

•Panasonic is not liable for incidental or consequential damages resulting from improper installation or operation.

•Keep the screws out of reach of children to prevent swallowing.

Wall-mount settings

1.Press [MENU].

2.Press [e, r, w, q] to select “Settings Menu” and press [OK].

3.Press [e, r, w, q] to select “Wall-mount Setting” and press [OK].

4.Press [e, r] to select “Yes” and press [OK].

Wall-mount Setting

Yes

No

Selecting “Yes” will rotate the display by 180 degrees.

The main unit controls cannot be used in this mode.

Select Item OK

5.Press [w, q] to select “Yes” and press [OK]. The power will be turned off and on automatically. When the power is turned on, the main unit’s screen display is turned upside down.

Note

•The audio will be stopped (paused) automatically, during playback.

„When using with the wall-mount setting

The following buttons and functions that can be used will be restricted.

Unusable buttons on	Except [POWER 8]
the main unit
Unusable buttons on	• [iPod/PLAY MENU]
the remote control	• [iPod/DISPLAY]
	• [iPod/q/h]
Timer audio playback	Automatically disabled (with the
function	setting contents preserved)
Menu items	• “iPod Play/Pause”
	• “iPod Display”
	• “iPod Play Menu”
	• “Audio Menu”
	• “Sync Music” in the “Photo
	Playback Settings”
Panasonic Logo	Automatically turned off
Power Save Setting	Automatically disabled
iPod/iPhone	Cannot be used
connection
USB connection	Cannot be used

Using with your PC

Operations

Reference

Using in a wall-mounted state

VQT2Z87

23