Monitor information, Error information

Using Web Browser Control

Monitor information page

Click [Projector control], then [Status information] to display the Status information page. This page displays the projector statuses established for the items shown below.

Displays the input switching status.

Displays temperature of projector’s intake air.

Displays temperature inside the projector.

Displays temperature around the lamp.

Displays the lamp1 lit hours.

Displays the lamp2 lit hours.

Displays the type of projector.

Displays used hours of the projector.

Displays self-diagnosis information.

Displays the firmware version of the projector main unit.

Error information page

When is displayed on the status information screen, click it to display the error details.

OK: Normal operation

FAILED: Occurrence of trouble

Note • Depending on the nature of the error, the projector may be placed in the standby mode for its own protection.

Page 40

Image 40

Panasonic PT-D4000U manual Monitor information, Error information, OK Normal operation Failed Occurrence of trouble

Contents

Operating Instructions Commercial Use Important Safety Notice Dear Panasonic CustomerPage Contents Precautions with regard to safety Remove empty batteries from the remote control at once Do not use or handle the batteries improperlyDo not disassemble the lamp unit Always disconnect all cables before moving the projector Do not use the old lamp unit AccessoriesDo not place the projector in extremely hot locations Precautions on handling Remote control Name and function of parts Bottom Front and side of the projector Status LED lights Rear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cable Installation geometry InstallationProjection schemes Projection distance by projection lens Screen aspect ratio Installation Calculation formulas for projection distance by lens types Setup precautions Connection Example of connecting with AV products Example of connecting with PCs Powering up the projector Making adjustment and selectionPress the I button. on the main unit or the remote control Projection Powering off the projector Direct power off function How to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Automatic adjustment Press the Status button on the remote controlStatus function Press the Shutter button again On-screen menus Structure of menu screens Menu items setting Resetting to the factory defaultBasic menu operations Returning to the previous Adjusting the picture Adjusting the position Clock Phase ZoomKeystone Digital Cinema Reality Input Resolution XGA ModeSxga Mode Clamp Position OPTION1 settings DVI Signal Level DVI EdidFUNC1 OSD Position OPTION2 settings InstallationProjector ID Altitude Lamp Relay Lamp SelectRS-232C Auto Power OFF PasswordSystem Information Date and Time Setting the network Connecting the PCSystem requirements Connection example Using Web Browser Control Accessing from the Web browserPassword change Click OK Basic control Change password buttonDetail control Monitor information Error informationOK Normal operation Failed Occurrence of trouble Mail set up When Failed has appeared for an item Parameter Description Mail set up page Continuing DNS server set up Authentication server set upPing test Contents of mail sent Adjust clock Network config Network status Using the PJLink protocol Supported commandsPJLink security authentication Command Control Description Remarks Setting the security Password ChangeDisplay Setting Control Device Setup Using the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connection Control commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and control Indication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filter When to replace the Lamp unit Replacing the lamp unitLamp After Lamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of time Ceiling Mount Bracket Safeguards Installation procedure Power does Not turn onNo image Image is blurred Specifications PT-D4000U Length of power cord Cabinet Outside dimensionsRemote control Power source Replacement lamp unit Compatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAM Dimensions Installation dimensions diagram Trademark Acknowledgement Concernant LA Sécurité Précautions concernant la sécurité Ne pas surcharger la prise de courantNe jamais tenter de modifier ou de démonter le projecteur Ne pas mettre d’objets étrangers dans le projecteur Pendant un orage, ne pas toucher le projecteur ou le câble Ne jamais démonter la lampe Ne pas empêcher la chaleur de s’échapper Ne pas utiliser la lampe usée Nettoyage et maintenance Précautions pour la manipulationMise au rebut Précautions pour l’utilisation Remplacement de la lampe Moment adéquat pour remplacer la lampeLampe Après La lampe est chaude si elle vient d’être utilisée Procédure de remplacement de la lampePréparez un tournevis Phillips à l’avance Technical Support Panasonic Projector Systems CompanyPanasonic Canada Inc