Replacing the lamp unit, Lamp, After, Hours | Panasonic PT-D4000U

Replacing the lamp unit

WARNING!

When replacing the lamp, allow it to cool for at least one hour before handling it.

•The lamp cover gets very hot, and touching it can cause burns.

Make sure that two lamp units are always installed.

Precautions on lamp unit replacement

Remove the power plug and confirm that the surroundings of the lamp unit have cooled off.

Be careful when handling a light source lamp. The lamp unit has high internal pressure. If improperly handled, explosion might result.

A used lamp unit may burst if it is handled violently.

For disposition of used lamps, request an industrial waste disposal contractor. If you continue to use a lamp after the replacement time, the lamp may break. Phillips screwdriver is necessary when replacing a lamp unit.

Take care not to slip your hand when using a screwdriver.

Note • It is not possible to turn on the power unless two lamp units are installed.

•A lamp unit is an optional part. Contact the dealer.

Replacement lamp unit model No.: ET-LAD40 (single bulb), ET-LAD40W (double bulbs)

•Other lamps than specified above cannot be used. Be sure to use the specified lamp.

When to replace the Lamp unit

The lamp units are consumable parts. The lamp brightness decreases gradually as the cumulative operating time increases, so periodic replacement is necessary. The replacement guideline is 3 000 hours, although the lamp may become dead (will not light) before 3 000 hours is reached depending on the characteristics of individual lamps and other factors such as the operating conditions and the installation environment. Therefore, it is recommended for the user to keep a spare lamp unit.

The risk of the lamp bursting increases after 3 000 hours of operation, so the lamp unit turns off automatically.

			On-screen indication		Lamp monitor
					LAMP
			REPLACE THE LAMP
			REPLACE THE LAMP

	After	The indication appears for 30
	After	seconds or until any control button
	2 800 hours	seconds or until any control button
	2 800 hours	is pressed.			The lamp monitor lights up red
		is pressed.

	After	The indication will not disappear			even in standby mode.
	After	The indication will not disappear
	3 000 hours	unless a control button is pressed.

52

Image 52

Panasonic PT-D4000U manual Replacing the lamp unit, When to replace the Lamp unit, After, Hours

Contents

Operating Instructions Commercial Use Important Safety Notice Dear Panasonic CustomerPage Contents Precautions with regard to safety Remove empty batteries from the remote control at once Do not use or handle the batteries improperlyDo not disassemble the lamp unit Always disconnect all cables before moving the projector Do not use the old lamp unit AccessoriesDo not place the projector in extremely hot locations Precautions on handling Remote control Name and function of parts Bottom Front and side of the projector Status LED lights Rear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cable Installation geometry InstallationProjection schemes Projection distance by projection lens Screen aspect ratio Installation Calculation formulas for projection distance by lens types Setup precautions Connection Example of connecting with AV products Example of connecting with PCs Powering up the projector Making adjustment and selectionPress the I button. on the main unit or the remote control Projection Powering off the projector Direct power off function How to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Automatic adjustment Press the Status button on the remote controlStatus function Press the Shutter button again On-screen menus Structure of menu screens Menu items setting Resetting to the factory defaultBasic menu operations Returning to the previous Adjusting the picture Adjusting the position Clock Phase ZoomKeystone Digital Cinema Reality Input Resolution XGA ModeSxga Mode Clamp Position OPTION1 settings DVI Signal Level DVI EdidFUNC1 OSD Position OPTION2 settings InstallationProjector ID Altitude Lamp Relay Lamp SelectRS-232C Auto Power OFF PasswordSystem Information Date and Time Setting the network Connecting the PCSystem requirements Connection example Using Web Browser Control Accessing from the Web browserPassword change Click OK Basic control Change password buttonDetail control Monitor information Error informationOK Normal operation Failed Occurrence of trouble Mail set up When Failed has appeared for an item Parameter Description Mail set up page Continuing DNS server set up Authentication server set upPing test Contents of mail sent Adjust clock Network config Network status Using the PJLink protocol Supported commandsPJLink security authentication Command Control Description Remarks Setting the security Password ChangeDisplay Setting Control Device Setup Using the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connection Control commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and control Indication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filter When to replace the Lamp unit Replacing the lamp unitLamp After Lamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of time Ceiling Mount Bracket Safeguards Installation procedure Power does Not turn onNo image Image is blurred Specifications PT-D4000U Length of power cord Cabinet Outside dimensionsRemote control Power source Replacement lamp unit Compatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAM Dimensions Installation dimensions diagram Trademark Acknowledgement Concernant LA Sécurité Précautions concernant la sécurité Ne pas surcharger la prise de courantNe jamais tenter de modifier ou de démonter le projecteur Ne pas mettre d’objets étrangers dans le projecteur Pendant un orage, ne pas toucher le projecteur ou le câble Ne jamais démonter la lampe Ne pas empêcher la chaleur de s’échapper Ne pas utiliser la lampe usée Nettoyage et maintenance Précautions pour la manipulationMise au rebut Précautions pour l’utilisation Remplacement de la lampe Moment adéquat pour remplacer la lampeLampe Après La lampe est chaude si elle vient d’être utilisée Procédure de remplacement de la lampePréparez un tournevis Phillips à l’avance Technical Support Panasonic Projector Systems CompanyPanasonic Canada Inc