SHARPNESS

“SHARPNESS” is used to adjust the crispness of the image.

: Sharpens the edge of the image. : Softens the edge of the image.

NOISE REDUCTION

In this mode, the video noise is reduced. OFF : No correction

1: Low

2: Middle

3: High

AI

Gray scale control is exercised to suit the images, and optimal images with a clear contrast are projected.

ON : AI compensation is enabled.

OFF : AI compensation is disabled.

SYSTEM SELECTOR

Set this according to the connected signal system.

(S-Video/Video terminal input signal) AUTO : This is the standard setting. The

received signal system is automatically identified.

AUTO NTSC NTSC4.43 PAL

PAL60 SECAM PAL-N PAL-M

Note • When signal deterioration or other factors prevent images from being displayed correctly with the “AUTO” setting, change the setting to match the connected signal system.

(RGB1/RGB2 terminal input signals) AUTO : This is the standard setting. The

received signal system is automatically identified.

When VGA60/480p signals are input

AUTO VGA60

YCBCR 480pRGB

When other than VGA60/480p are input

AUTO RGB

YPBPR (YCBCR)

For the signals which are supported, refer to page 61.

Adjusting the position

POSITION

SHIFT

ASPECT

4:3

ZOOM

 

CLOCK PHASE

+16

KEYSTONE

 

MENU SELECT

SUB MENU

SHIFT

The position where the images are displayed can be moved here.

: The position is moved horizontally. : The position is moved vertically.

ASPECT

AUTO : (For S-Video/Video signals only)

At this setting, when S1 video signals*1 are identified as being input to the S-Video connector or video ID signals are identified as being input to the video connector, the images are displayed after automatically being converted to the 16:9 aspect ratio.

16:9 : At this setting, when standard signals*2 are input, the images are converted to the 16:9 aspect ratio and displayed. When wide-screen signals*3 are input, the images are displayed with their inherent aspect ratio intact.

4:3 : At this setting, when standard signals*2 are input, the images are displayed with their inherent aspect ratio intact. When wide-screen signals*3 are input, they are converted by the PT-D5700E/PT- D5700EL to the 4:3 aspect ratio and displayed. With the PT-DW5100E/PT-DW5100EL, the images are reduced in size and displayed without converting their aspect ratio so that they will fit onto a screen with a 4:3 aspect ratio.

S4:3 : Select this setting when using a 16:9 screen.

H FIT : Pictures are displayed using all the panel pixels in the horizontal direction. When a signal has an aspect ratio taller than that of the panel pixel*4, the image will be displayed with the top and bottom portions cut off.

V FIT : Pictures are displayed using all the panel pixels in the vertical direction. When a signal has an aspect ratio wider than that of the panel pixel*4, the image will be displayed with the left and right sides cut off.

HV FIT : The image is displayed on all the panel pixels*4. When the aspect ratio of the input signal is different from that of the panel pixel*4, the signal is transformed to the aspect ratio of the panel pixel*4 and then displayed.

*1 S1 video signals are 16:9 video signals to which is added the detection signal output from the video deck or other unit which supports the wide-screen format.

*2 Here, the standard signal means 4:3 or 5:4 input signals.

*3 Here, the wide-screen signals means 16:9, 15:9 or 15:10 input signals *4 Panel pixel aspect ratio is 4:3 in the case of PT-D5700E/PT-D5700EL

and 15:9 for PT-DW5100E/PT-DW5100EL.

Attention • If you choose an aspect ratio that does not match the source video’s aspect ratio, you

will see a picture with an aspect ratio not the same as that of the original picture. Choose the appropriate aspect ratio carefully to match that of the original picture.

(Continued on the next page)

ENGLISH

29

Page 29
Image 29
Panasonic PT-DW5100EL, PT-D5700EL manual Adjusting the position