Panasonic WJ-HD309 117, Control Camera CH, Unit AddressSystem, RS232C Setup Settings for RS232C

●Baud Rate

Select the communication speed for data transmission with a connected device from the following.

4 800/9 600/19 200 bps

●Control Camera CH

It is possible to assign camera channels to the RS485 ports 1 and 2 as shown below.

[Screenshot 1]

Start operation from the "RS485 Setup" menu.

SETUP MENU	Maintenance	Recording	Event	Schedule	LIVE
	Switcher	Display	Comm	System
	■ Baud Rate
Camera Control				19200
PS.DATA Setup	■ Control Camera CH			SETUP
	■ Data Bit			8
RS485 Setup	■ Parity			NONE
RS232C Setup	■ Stop Bit			1

NW Setup 1

NW Setup 2

NTP Setup

z Move the cursor to "Control Camera CH" using the arrows button (CD) and press the SET button.

[Screenshot 2]

The "Control Camera CH" pop-up window will be displayed.

SETUP MENU
			Maintenance		Recording	Event	Schedule		LIVE
			Switcher		Display	Comm		System
	■	Control Camera CH					19200
Camera	Control		■	Baud Rate				SETUP
			■	Control Camera CH		CAMERA
PS.DATA
	SetupCAMERA				TERM		8	TERM
			■	Data	PORT1	CAM9		PORT2
RS485	Setup	CAM1		Parity
			■		PORT1	CAM10		PORT2
RS232C	Setup	CAM2		Stop
			■		PORT1
NW Setup 1		CAM3				CAM11		PORT2
NW Setup 2		CAM4			PORT1	CAM12		PORT2
		CAM5			PORT1	CAM13		PORT2
NTP Setup
		CAM6			PORT1	CAM14		PORT2
		CAM7			PORT1	CAM15		PORT2
		CAM8			PORT1	CAM16		PORT2
						O K		CANCEL

xMove the cursor to a desired cell in the "TERM" column using the arrows button.

[Screenshot 3]

The cursor will move to the selected cell in the "TERM" col- umn.

SETUP MENU Maintenance				Recording	Event	Schedule		LIVE
		Switcher		Display	Comm		System
	■	Control Camera CH				19200
Camera	Control	■	Baud Rate				SETUP
		■	Control Camera CH		CAMERA
PS.DATA
	SetupCAMERA			TERM		8	TERM
		■	Data	PORT1	CAM9		PORT2
RS485	Setup	CAM1	Parity
		■		PORT1	CAM10		PORT2
RS232C	Setup	CAM2	Stop
		■		PORT1
NW Setup 1		CAM3			CAM11		PORT2
NW Setup 2		CAM4		PORT1	CAM12		PORT2
NTP Setup		CAM5		PORT1	CAM13		PORT2
		CAM6		PORT1	CAM14		PORT2
		CAM7		PORT1	CAM15		PORT2
		CAM8		PORT1	CAM16		PORT2
					O K		CANCEL

cSelect a port by rotating the jog dial. PORT 1: Control through the RS485 port 1. PORT 2: Control through the RS485 port 2.

Repeat steps 2 and 3 to assign other camera channels to be controlled through the RS485 ports.

v Move the cursor to "OK" using the arrows button and press the SET button.

→Camera channels and ports to be controlled will be assigned and the "Control Camera CH" menu will be closed.

Notes:

•When you move the cursor to "CANCEL" in step 4 and press the SET button, the settings will be can- celed and the "Camera Number Setup" menu will be closed.

•The assignment of camera channels will not be applied until the SET button is pressed after moving the cursor to "OK" in the step 4.

•The unit number of the camera will be congruent with the camera number.

●Data Bit

The data length for communication will be displayed. It is impossible to change the value for this setting.

●Parity

Methods to check a transmission error at communication will be displayed.

It is impossible to change the value for this setting.

●Stop Bit

Number of stop bit will be displayed.

It is impossible to change the value for this setting.

r[RS232C Setup] Settings for RS232C

Perform the following settings for RS232C.

SETUP MENU	Maintenance	Recording	Event	Schedule	LIVE
	Switcher	Display	Comm	System
	■ Unit Address(System)
Camera Control				001
PS.DATA Setup	■ Baud Rate			9600
	■ Data Bit			8
RS485 Setup
	■ Parity			NONE
RS232C Setup	■ Stop Bit			1
	■ Retry Timing			OFF
NW Setup 1

NW Setup 2

NTP Setup

●Unit Address(System)

A unit address (System) is a unique number assigned to each system device. The addresses must be unique to identify system devices when connecting multiple system devices.

Numbers, "001"-"099", are to be assigned as the unit addresses for the system devices.

●Baud Rate

Select the communication speed for data transmission with a connected device from the following.

9 600/19 200/38 400 bps

117