●Mode 3
The signals from stereo or mono input lines are separately output through the STEREO OUTPUT, MONO OUTPUT and SUB OUTPUT jack. For example, this connection is used for zone amplification in a shop.
•The signals from the MONO INPUT 1 and 2 connectors are output through the STEREO OUTPUT and MONO OUTPUT jacks. (Input for
•The signals from the MONO INPUT 3 connector are output through the STEREO OUTPUT jack (Zone 1) and the signals from MONO INPUT 4 connector are output through the MONO OUTPUT jack (Zone 2). (Input for broadcasting in each zone)
•The signals from the STEREO INPUT 1 to 4 jacks are output through the STEREO OUTPUT (Zone 1) and MONO OUTPUT (Zone 2) jack.
•Amplification in other areas is possible by assigning another BGM to the SUB OUTPUT jack and mixing with
•The signals from the MULTI INPUT ST jack or MULTI INPUT MONO connector are output to the STEREO OUTPUT, MONO OUTPUT and SUB OUTPUT jacks.*
*The output line is assigned with the assign button setting. (Refer to p. 19.)
Wireless microphone | |
| in the hall |
Wireless | Antenna for |
microphone | wireless microphone |
Wireless |
|
microphone |
|
Diversity wireless receiver | |
Microphone |
for a host |
Microphone |
on the platform |
CD
MD
TAPE
Video sound
Mono output is also available in Zone 1. (Switch inside)
Speakers
Power amplifier
Digital Multi
Equalizer
Zone 2
MONO 
INPUT 1 to 4
STEREO |
|
INPUT 1 to 4 | Zone 1 Zone 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ST |
| MONO SUB | STEREO OUT |
| MONO OUT | Audio Mixer | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 | 6 |
| 4 | 6 |
|
|
| 1 |
| 2 | MONO |
| 3 |
|
| 4 |
| 1 |
| 2 | STEREO |
| 3 |
|
| 4 |
| MULTI IN | INPUT |
|
|
|
| SUB OUT | ||||
4 | 6 |
| 4 | 6 |
| 4 | 6 |
| 4 | 6 | 4 | 6 |
| 4 | 6 |
| 4 | 6 |
| 4 | 6 |
| 4 | 6 | REAK |
|
|
|
| 4 | 6 |
POWER | 8 | 2 |
| 8 | 2 |
| 8 | 2 |
| 8 | 2 | 8 | 2 |
| 8 | 2 |
| 8 | 2 |
| 8 | 2 |
| 8 | 2 | 8 | 2 |
|
| 8 | 8 |
2 |
|
|
|
|
|
|
| LINE IN |
|
|
|
| 2 | ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
0 | 10 |
| 0 | 10 |
| 0 | 10 |
| 0 | 10 | 0 | 10 |
| 0 | 10 |
| 0 | 10 |
| 0 | 10 |
| 0 | 10 | 0 | 10 |
| 0 | 10 | 0 | 10 |
MONO 1 to 2
(Zone 1 and 2)
MONO3
(Zone 1)
MONO4 (Zone 2)
Any mono and stereo input can be assigned to the SUB OUTPUT jack as Zone 3
To adjust the output levels
Requires setting of an internal switch.
In the case shown in the figure, the volume of Zone 1 is adjusted with the STEREO OUT knob ,and that of Zone 2 is adjust- ed with the MONO OUT knob.
To output the mono mix signal (the same signal through the STEREO OUTPUT jack)
The internal switch setting is necessary.
Refer to a service manual procurable in your area.
DIP switch setting
Switches A and B are set to OFF.
ON
OFF
Switch B
Switch A
17
