Manuals / Panduit / Computer Equipment / Printer

Panduit PTR3E manual Replacing The Fuse, Cleaning and Maintenance, Supplies needed, 250V 3A Fuse

Models: PTR3E

1 59

Download 59 pages 9.77 Kb

Page 53

Image 53

Section 4: Cleaning and Maintenance

REPLACING THE FUSE

Supplies needed:

250V 3A Fuse

1.Turn the printer power OFF and remove the power cable.

2.On the back of the printer, locate the Fuse Cap on the right-hand side of the AC connector.

3.Unscrew the cap and remove the defective fuse.

4.Replace with a new 250V 3A fuse.

5.Screw the cap back onto the printer and replace the power cord.

Page 53

Image 53

Panduit PTR3E manual Replacing The Fuse, Cleaning and Maintenance, Supplies needed, 250V 3A Fuse

Contents

PTR3E Thermal Transfer Printer Operator and Technical Reference ManualCumming, GA Phone Fax Panduit Corp Identification Products Division 1819 Atlanta HwyCopyright Panduit Corp. 2001. All Rights Reserved Panduit PTR3EDO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE SAFETY PRACTICESDO NOT OPERATE IN WET OR DAMP AREAS DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENTINFORMATION TO USER WARRANTY INFORMATIONPTR3E OPERATOR MANUAL PREFACESECTION 2. INSTALLATION SECTION 3. CONFIGURATIONSECTION 2. INSTALLATION TABLE OF CONTENTSSECTION 3. CONFIGURATION SECTION 4. CLEANING AND MAINTENANCESECTION 6. TROUBLESHOOTING SECTION 5. INTERFACE SPECIFICATIONSInitial Checklist Using the IEEE1284 Parallel Interface Using the RS232C Serial Interface Error SignalsPage INTRODUCTION SECTION PRINTER OVERVIEWSPECIFICATION GENERAL PRINTER SPECIFICATIONSSection 1. Printer Overview PTR3EPTR3E SPECIFICATIONSection 1. Printer Overview SPECIFICATION CHARACTER FONTSSection 1. Printer Overview PTR3ESPECIFICATION BAR CODESSection 1. Printer Overview PTR3ESPECIFICATION PHYSICALSection 1. Printer Overview PTR3EINTRODUCTION SECTION INSTALLATIONUNPACKI G AND PARTS IDENTIFICATION packedNOTETheexactlyshippingasshownhere,butarethe PTR3E PackingPrinter SETTING UP THE PRINTEROperatorManual ExtraRibbonCoreSideAccess TopAccessSwitch CoverPowerDoor TopAccessDoorSideAccessLabelRoll LOADING LABELSPage Sensor AdjustmentAssembly 3. Locate the Extra Ribbon Core supplied with the printer. Place LOADING THERibbonSpindleRIBBONRewindady aded 8. If the b ls are allose the Print He Ass mbly by push downwardDSW2 ERROROPERATOR PANEL LABELP use Connector Access PanelEXT Port Connector AC Power InPage LABEL SENSOR ADJUSTMENT DSW2-1SETTING SECTION CONFIGURATIONPRINTER DIP SWITCH CONFIGURATION DIP Switch PanelsStadardNoETTING n-Std OFFON123DSW245678control. DSW2OFFON-7 Print Speed Adjustment DSW2-8 . See page DSW3-4SETTINGMode Selection 3-1 and DSW3-2 . Selects the operating mode of the printerOFFN DSW3-7SETTING4OFFON12 RS232 Transmit/ReceiveDefault S DSW1-7DSW1-8SETTINGSwitch S OFFNMODE PRINTER ADJUSTMENTSKEY SEQUENCE INITIAL DISPLAYINITIALIZING ROM ONLINE QTY000000 OFFLINE 000000 Normal ModePRINT SPEED 2 4 6 8 PRINT DARKNESS 1 2 3 4PITCH OFFSET ± 00mm SensorPositionCANCEL PRINT JOB YES NO CANCEL PRINT JOB COMPLETED ADVANCED MODE INITIALIZING ROM ADVANCED MODE ZERO SLASH YES NO AUTO ONLINE YES NOPRINT OFFSET V+0000 H+000 IGNORE CR/LF YES NO SERVICE MODE CHARACTER PITCH PROP FIXED ADVANCED MODEADVANCED MODE SERVICE MODE GAP INPUTEURO CODE D5 SELECT LANGUAGE ENGLISH AUTO ONLINE FEED YES NO FEED ON ERROR YES NO REPRINT W/FEED YES NOFORWARD/BACKFEED DISTANCE DEFAULT FORWARD/BACKFEED DISTANCE XXXmm PRIORITY SETTING COMMAND LCD SERVICE MODE TEST PRINT MODEDEFAULT SETTING YES NO DEFAULT SETTING MODEDEFAULT SETTING COMPLETED INITIALIZING ROMPOTENTIOMETER ADJUSTMENTS HEX DUMP MODEINITIALIZING ROM ONLINE QTY000000 PITCHDISPLAY BACKFEED OFFSETPRINT commend code speed and darkness rangesDISPLAY COUNTER VALUES FACTORY MODECOUNTER CLEAR NONE MAINTENANCE MODE DIPSW2-4 ON-OFFPage PROCEDURES SECTION CLEANING AND MAINTENANCEADJUSTING THE PRINT QUALITY INTRODUCTIONNOTEcommandThecode PRINT Print Potentiometerprint,thedarkness darknessinallofthe2. Open the Top Access and Side Access doors CLEANING THE PRINT HEAD, PLATEN AND ROLLERSCleaning the Print Head and Platen 2. Open the Top Access and Side Access doors CLEANING THE SENSORSCleaning the Rollers and Guides 2. Open the Top and Side Access doors REPLACING THE PRINT HEADDOhavemouning NOT thed,centeritwillSection 4 Cleaning and Maintenance REPLACING THE FUSESupplies needed 250V 3A FuseSection 4 Cleaning and Maintenance INTERFACE TYPES SECTION INTERFACE SPECIFICATIONSIEEE1284 PARALLEL INTERFACE ELECTRICAL SPECIFICATIONSGENERAL SPECIFICATIONS RS232C SERIAL INTERFACEELECTRICAL SPECIFICATIONS ConnectorUSING THE IEEE1284 PARALLEL INTERFACE SECTION TROUBLESHOOTINGINITIAL CHECKLIST USING THE RS232C SERIAL INTERFACE Section 6. Troubleshooting ERROR SIGNALSERROR CONDITION AUDIBLE